Skip to content

孙克 / RC1250-AssemblyLine

转到一个项目
切换导航栏
切换导航栏固定状态
Commit c0a0de6a 由 LN
选项

1

1 个父辈 ed18caa3
内嵌 并排
正在显示 26 个修改的文件 包含 815 行增加 和 437 行删除
doc/RC1250佳世达IO配置10-10.xlsx 0 → 100644
此文件类型无法预览
source/AssemblyLineClient/FrmFeedingEquip.cs
...@@ -230,6 +230,19 @@ namespace OnlineStore.AssemblyLine ...@@ -230,6 +230,19 @@ namespace OnlineStore.AssemblyLine
lblStoreStatus.Text = KTK_Store.GetRunStr(equipBean.lineStatus, equipBean.runStatus); lblStoreStatus.Text = KTK_Store.GetRunStr(equipBean.lineStatus, equipBean.runStatus);
lblThisSta.Text = equipBean.WarnMsg; lblThisSta.Text = equipBean.WarnMsg;
txtP1.Text = equipBean.Config.BatchAxisP1.ToString(); txtP1.Text = equipBean.Config.BatchAxisP1.ToString();
if (equipBean.Config.SidesWayNum > 0)
{
btnSwLocationCylinder.Visible = true;
btnSWTop.Visible = true;
btnFL_TopCylinder.Visible = false;
}
else
{
btnSwLocationCylinder.Visible = false ;
btnSWTop.Visible = false ;
btnFL_TopCylinder.Visible = true ;
}
IsLoad = true; IsLoad = true;
} }
......
source/DeviceLibrary/LineConfig/Config_FeedingEquip_1.csv
...@@ -3,6 +3,7 @@ PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,, ...@@ -3,6 +3,7 @@ PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,,
PRO,0,扫码的相机名称(多个用#分隔),CameraNameList,Name1#Name1,,,,, PRO,0,扫码的相机名称(多个用#分隔),CameraNameList,Name1#Name1,,,,,
PRO,0,移栽上下运动是否使用伺服,UpDownUseAxis,1,,,,, PRO,0,移栽上下运动是否使用伺服,UpDownUseAxis,1,,,,,
PRO,0,对应的横移模块,SidesWayNum,1,,,,, PRO,0,对应的横移模块,SidesWayNum,1,,,,,
PRO,0,是否是用来出料,IsCanOut,0,,,,,
,,,,,,,,, ,,,,,,,,,
AXIS,0,批量上料轴,Batch_Axis,2,COM1,0,,, AXIS,0,批量上料轴,Batch_Axis,2,COM1,0,,,
PRO,0,批量上料轴待机点 P1,BatchAxisP1,2000,,,,, PRO,0,批量上料轴待机点 P1,BatchAxisP1,2000,,,,,
......
source/DeviceLibrary/LineConfig/Config_FeedingEquip_2.csv
...@@ -3,6 +3,7 @@ PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,, ...@@ -3,6 +3,7 @@ PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,,
PRO,0,扫码的相机名称(多个用#分隔),CameraNameList,Name1#Name1,,,,, PRO,0,扫码的相机名称(多个用#分隔),CameraNameList,Name1#Name1,,,,,
PRO,0,移栽上下运动是否使用伺服,UpDownUseAxis,1,,,,, PRO,0,移栽上下运动是否使用伺服,UpDownUseAxis,1,,,,,
PRO,0,对应的横移模块,SidesWayNum,0,,,,, PRO,0,对应的横移模块,SidesWayNum,0,,,,,
PRO,0,是否是用来出料,IsCanOut,0,,,,,
,,,,,,,,, ,,,,,,,,,
AXIS,0,批量上料轴,Batch_Axis,2,COM1,0,,, AXIS,0,批量上料轴,Batch_Axis,2,COM1,0,,,
PRO,0,批量上料轴待机点 P1,BatchAxisP1,2000,,,,, PRO,0,批量上料轴待机点 P1,BatchAxisP1,2000,,,,,
...@@ -81,8 +82,8 @@ DO,0,SL2上料气缸放松SOL,SL_FeedCylinder_Slack,0,192.168.200.24,0,SL2上料气缸放松 ...@@ -81,8 +82,8 @@ DO,0,SL2上料气缸放松SOL,SL_FeedCylinder_Slack,0,192.168.200.24,0,SL2上料气缸放松
DO,0,SL2上料气缸夹紧SOL,SL_FeedCylinder_Tighten,1,192.168.200.24,0,SL2上料气缸夹紧SOL,Y162,Y162 DO,0,SL2上料气缸夹紧SOL,SL_FeedCylinder_Tighten,1,192.168.200.24,0,SL2上料气缸夹紧SOL,Y162,Y162
DO,0,SL2托盘定位气缸1前进SOL,SL_TrayLocationCylinder_Before,2,192.168.200.24,0,SL2托盘定位气缸1前进SOL,Y163,Y163 DO,0,SL2托盘定位气缸1前进SOL,SL_TrayLocationCylinder_Before,2,192.168.200.24,0,SL2托盘定位气缸1前进SOL,Y163,Y163
DO,0,SL2托盘定位气缸1后退SOL,SL_TrayLocationCylinder_After,3,192.168.200.24,0,SL2托盘定位气缸1后退SOL,Y164,Y164 DO,0,SL2托盘定位气缸1后退SOL,SL_TrayLocationCylinder_After,3,192.168.200.24,0,SL2托盘定位气缸1后退SOL,Y164,Y164
DO,0,FL1阻挡1下降SOL,FL_Stop1Down,4,192.168.200.24,0,FL1阻挡1下降SOL,Y165,Y165 DO,0,FL1阻挡1下降SOL,FL_StopCylinder_Down1,4,192.168.200.24,0,FL1阻挡1下降SOL,Y165,Y165
DO,0,FL1阻挡2下降SOL,FL_Stop2Down,5,192.168.200.24,0,FL1阻挡2下降SOL,Y166,Y166 DO,0,FL1阻挡2下降SOL,FL_StopCylinder_Down2,5,192.168.200.24,0,FL1阻挡2下降SOL,Y166,Y166
DO,0,FL1顶升上升SOL,FL_TopCylinder_Up,6,192.168.200.24,0,FL1顶升上升SOL,Y167,Y167 DO,0,FL1顶升上升SOL,FL_TopCylinder_Up,6,192.168.200.24,0,FL1顶升上升SOL,Y167,Y167
DO,0,FL1顶升下降SOL,FL_TopCylinder_Down,7,192.168.200.24,0,FL1顶升下降SOL,Y168,Y168 DO,0,FL1顶升下降SOL,FL_TopCylinder_Down,7,192.168.200.24,0,FL1顶升下降SOL,Y168,Y168
DO,0,SL2提升伺服刹车ON,SL_UpAxis_BreakOn,8,192.168.200.24,0,SL2提升伺服刹车ON,Y169,Y169 DO,0,SL2提升伺服刹车ON,SL_UpAxis_BreakOn,8,192.168.200.24,0,SL2提升伺服刹车ON,Y169,Y169
......
source/DeviceLibrary/LineConfig/Config_FeedingEquip_3.csv
...@@ -3,6 +3,7 @@ PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,, ...@@ -3,6 +3,7 @@ PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,,
PRO,0,扫码的相机名称(多个用#分隔),CameraNameList,Name1#Name1,,,,, PRO,0,扫码的相机名称(多个用#分隔),CameraNameList,Name1#Name1,,,,,
PRO,0,移栽上下运动是否使用伺服,UpDownUseAxis,1,,,,, PRO,0,移栽上下运动是否使用伺服,UpDownUseAxis,1,,,,,
PRO,0,对应的横移模块,SidesWayNum,2,,,,, PRO,0,对应的横移模块,SidesWayNum,2,,,,,
PRO,0,是否是用来出料,IsCanOut,0,,,,,
,,,,,,,,, ,,,,,,,,,
AXIS,0,批量上料轴,Batch_Axis,2,COM1,0,,, AXIS,0,批量上料轴,Batch_Axis,2,COM1,0,,,
PRO,0,批量上料轴待机点 P1,BatchAxisP1,2000,,,,, PRO,0,批量上料轴待机点 P1,BatchAxisP1,2000,,,,,
......
source/DeviceLibrary/LineConfig/Config_FeedingEquip_4.csv
...@@ -3,6 +3,7 @@ PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,, ...@@ -3,6 +3,7 @@ PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,,
PRO,0,扫码的相机名称(多个用#分隔),CameraNameList,Name1#Name1,,,,, PRO,0,扫码的相机名称(多个用#分隔),CameraNameList,Name1#Name1,,,,,
PRO,0,移栽上下运动是否使用伺服,UpDownUseAxis,1,,,,, PRO,0,移栽上下运动是否使用伺服,UpDownUseAxis,1,,,,,
PRO,0,对应的横移模块,SidesWayNum,3,,,,, PRO,0,对应的横移模块,SidesWayNum,3,,,,,
PRO,0,是否是用来出料,IsCanOut,1,,,,,
,,,,,,,,, ,,,,,,,,,
AXIS,0,批量上料轴,Batch_Axis,2,COM1,0,,, AXIS,0,批量上料轴,Batch_Axis,2,COM1,0,,,
PRO,0,批量上料轴待机点 P1,BatchAxisP1,2000,,,,, PRO,0,批量上料轴待机点 P1,BatchAxisP1,2000,,,,,
......
source/DeviceLibrary/LineConfig/Config_ProvidingEquip_1.csv
类型,分类编号,说明,名称,属性值,设备名称,默认值,描述,电器定义,代码定义 类型,分类编号,说明,名称,属性值,设备名称,默认值,描述,电器定义,代码定义
PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,, PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,,
PRO,0,对应的横移模块,SidesWayNum,0,,,,,
\ No newline at end of file \ No newline at end of file
source/DeviceLibrary/LineConfig/Config_ProvidingEquip_2.csv
类型,分类编号,说明,名称,属性值,设备名称,默认值,描述,电器定义,代码定义 类型,分类编号,说明,名称,属性值,设备名称,默认值,描述,电器定义,代码定义
PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,, PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,,
PRO,0,对应的横移模块,SidesWayNum,0,,,,,
\ No newline at end of file \ No newline at end of file
source/DeviceLibrary/LineConfig/Config_ProvidingEquip_3.csv
类型,分类编号,说明,名称,属性值,设备名称,默认值,描述,电器定义,代码定义 类型,分类编号,说明,名称,属性值,设备名称,默认值,描述,电器定义,代码定义
PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,, PRO,0,设备是否处于调试状态（1=调试，0=正常）,IsDebug,1,,,,,
PRO,0,对应的横移模块,SidesWayNum,0,,,,,
\ No newline at end of file \ No newline at end of file
source/DeviceLibrary/LineConfig/MoveEquip/Config_MoveEquip_17.csv
...@@ -36,10 +36,10 @@ DI,18,进仓18夹料放松端,ClampCylinder_Tighten,1,192.168.200.46,0,进仓18夹料放松端 ...@@ -36,10 +36,10 @@ DI,18,进仓18夹料放松端,ClampCylinder_Tighten,1,192.168.200.46,0,进仓18夹料放松端
DI,18,进仓18升降上升端,UpDownCylinder_Up,2,192.168.200.46,0,进仓18升降上升端,X553,X553 DI,18,进仓18升降上升端,UpDownCylinder_Up,2,192.168.200.46,0,进仓18升降上升端,X553,X553
DI,18,进仓18升降下降端,UpDownCylinder_Down,3,192.168.200.46,0,进仓18升降下降端,X554,X554 DI,18,进仓18升降下降端,UpDownCylinder_Down,3,192.168.200.46,0,进仓18升降下降端,X554,X554
DI,204,出料4阻挡1托盘检测,StopCylinder_Check1,4,192.168.200.46,0,出料4阻挡1托盘检测,X555,X555 DI,204,出料4阻挡1托盘检测,StopCylinder_Check1,4,192.168.200.46,0,出料4阻挡1托盘检测,X555,X555
DI,1000,环形线横移4托盘检测,SW4_SideWay_TrayCheck,5,192.168.200.46,0,环形线横移4托盘检测,X556,X556 DI,204,出料4阻挡2托盘检测,StopCylinder_Check2,5,192.168.200.46,0,出料4阻挡2托盘检测,X556,X556
DI,1000,环形线横移4料盘检测1,SW4_SideWay_ReelCheck,6,192.168.200.46,0,环形线横移4料盘检测1,X557,X557 DI,204,出料4料盘检测,TrayCheck,6,192.168.200.46,0,出料4料盘检测,X557,X557
DI,1000,环形线横移4顶升上升端,SW4_TopCylinder_Up,7,192.168.200.46,0,环形线横移4顶升上升端,X558,X558 DI,204,出料4顶升上升端,TopCylinder_UP,7,192.168.200.46,0,出料4顶升上升端,X558,X558
DI,1000,环形线横移4顶升下降端,SW4_TopCylinder_Down,8,192.168.200.46,0,环形线横移4顶升下降端,X559,X559 DI,204,出料4顶升下降端,TopCylinder_Down,8,192.168.200.46,0,出料4顶升下降端,X559,X559
DI,204,出料4前后气缸前进端,BeforeAfterCylinder_Before,9,192.168.200.46,0,出料4前后气缸前进端,X560,X560 DI,204,出料4前后气缸前进端,BeforeAfterCylinder_Before,9,192.168.200.46,0,出料4前后气缸前进端,X560,X560
DI,204,出料4前后气缸后退端,BeforeAfterCylinder_After,10,192.168.200.46,0,出料4前后气缸后退端,X561,X561 DI,204,出料4前后气缸后退端,BeforeAfterCylinder_After,10,192.168.200.46,0,出料4前后气缸后退端,X561,X561
DI,204,出料4夹料气缸夹紧端,ClampCylinder_Slack,11,192.168.200.46,0,出料4夹料气缸夹紧端,X562,X562 DI,204,出料4夹料气缸夹紧端,ClampCylinder_Slack,11,192.168.200.46,0,出料4夹料气缸夹紧端,X562,X562
...@@ -70,8 +70,8 @@ DO,18,进仓18升降上升SOL,UpDownCylinder_Up,2,192.168.200.46,0,进仓18升降上升SOL,Y ...@@ -70,8 +70,8 @@ DO,18,进仓18升降上升SOL,UpDownCylinder_Up,2,192.168.200.46,0,进仓18升降上升SOL,Y
DO,18,进仓18升降下降SOL,UpDownCylinder_Down,3,192.168.200.46,0,进仓18升降下降SOL,Y554,Y554 DO,18,进仓18升降下降SOL,UpDownCylinder_Down,3,192.168.200.46,0,进仓18升降下降SOL,Y554,Y554
DO,204,出料4阻挡1下降SOL,StopCylinder_Down1,4,192.168.200.46,0,出料4阻挡1下降SOL,Y555,Y555 DO,204,出料4阻挡1下降SOL,StopCylinder_Down1,4,192.168.200.46,0,出料4阻挡1下降SOL,Y555,Y555
DO,204,出料4阻挡2下降SOL,StopCylinder_Down2,5,192.168.200.46,0,出料4阻挡2下降SOL,Y556,Y556 DO,204,出料4阻挡2下降SOL,StopCylinder_Down2,5,192.168.200.46,0,出料4阻挡2下降SOL,Y556,Y556
DO,1000,环形线横移4顶升上升SOL,SW4_TopCylinder_Up,6,192.168.200.46,0,环形线横移4顶升上升SOL,Y557,Y557 DO,204,出料4顶升上升SOL,TopCylinder_UP,6,192.168.200.46,0,出料4顶升上升SOL,Y557,Y557
DO,1000,环形线横移4顶升下降SOL,SW4_TopCylinder_Down,7,192.168.200.46,0,环形线横移4顶升下降SOL,Y558,Y558 DO,204,出料4顶升下降SOL,TopCylinder_Down,7,192.168.200.46,0,出料4顶升下降SOL,Y558,Y558
DO,204,出料4前后气缸前进SOL,BeforeAfterCylinder_Before,8,192.168.200.46,,出料4前后气缸前进SOL,Y559,Y559 DO,204,出料4前后气缸前进SOL,BeforeAfterCylinder_Before,8,192.168.200.46,,出料4前后气缸前进SOL,Y559,Y559
DO,204,出料4前后气缸后退SOL,BeforeAfterCylinder_After,9,192.168.200.46,,出料4前后气缸后退SOL,Y560,Y560 DO,204,出料4前后气缸后退SOL,BeforeAfterCylinder_After,9,192.168.200.46,,出料4前后气缸后退SOL,Y560,Y560
DO,204,出料4夹料气缸夹紧SOL,ClampCylinder_Slack,10,192.168.200.46,,出料4夹料气缸夹紧SOL,Y561,Y561 DO,204,出料4夹料气缸夹紧SOL,ClampCylinder_Slack,10,192.168.200.46,,出料4夹料气缸夹紧SOL,Y561,Y561
...@@ -79,5 +79,11 @@ DO,204,出料4夹料气缸放松SOL,ClampCylinder_Tighten,11,192.168.200.46,,出料4夹料气 ...@@ -79,5 +79,11 @@ DO,204,出料4夹料气缸放松SOL,ClampCylinder_Tighten,11,192.168.200.46,,出料4夹料气
DO,204,出料4上下气缸上升SOL,UpDownCylinder_Up,12,192.168.200.46,,出料4上下气缸上升SOL,Y563,Y563 DO,204,出料4上下气缸上升SOL,UpDownCylinder_Up,12,192.168.200.46,,出料4上下气缸上升SOL,Y563,Y563
DO,204,出料4上下气缸下降SOL,UpDownCylinder_Down,13,192.168.200.46,,出料4上下气缸下降SOL,Y564,Y564 DO,204,出料4上下气缸下降SOL,UpDownCylinder_Down,13,192.168.200.46,,出料4上下气缸下降SOL,Y564,Y564
,,,,14,192.168.200.46,,,Y565,Y565 ,,,,14,192.168.200.46,,,Y565,Y565
,,,,15,192.168.200.46,,,Y566,Y566
,,,,,,,,, ,,,,,,,,,
DI,1000,环形线横移4托盘检测,SW4_SideWay_TrayCheck,5,192.168.200.46,0,环形线横移4托盘检测,X556,X556
DI,1000,环形线横移4料盘检测1,SW4_SideWay_ReelCheck,6,192.168.200.46,0,环形线横移4料盘检测1,X557,X557
DI,1000,环形线横移4顶升上升端,SW4_TopCylinder_Up,7,192.168.200.46,0,环形线横移4顶升上升端,X558,X558
DI,1000,环形线横移4顶升下降端,SW4_TopCylinder_Down,8,192.168.200.46,0,环形线横移4顶升下降端,X559,X559
,,,,,,,,,
DO,1000,环形线横移4顶升上升SOL,SW4_TopCylinder_Up,6,192.168.200.46,0,环形线横移4顶升上升SOL,Y557,Y557
DO,1000,环形线横移4顶升下降SOL,SW4_TopCylinder_Down,7,192.168.200.46,0,环形线横移4顶升下降SOL,Y558,Y558
source/DeviceLibrary/assemblyLine/EquipBase.cs
...@@ -194,7 +194,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -194,7 +194,7 @@ namespace OnlineStore.DeviceLibrary
/// <summary> /// <summary>
/// 下降所有阻挡气缸 /// 下降所有阻挡气缸
/// </summary> /// </summary>
internal void OpenStopCylinder() internal virtual void OpenStopCylinder()
{ {
if (baseConfig.DType.Equals(DeviceType.MoveEquip) || baseConfig.DType.Equals(DeviceType.ProvidingEquip)) if (baseConfig.DType.Equals(DeviceType.MoveEquip) || baseConfig.DType.Equals(DeviceType.ProvidingEquip))
{ {
...@@ -212,7 +212,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -212,7 +212,7 @@ namespace OnlineStore.DeviceLibrary
IOMove(IO_Type.TopCylinder_Down, IO_VALUE.HIGH); IOMove(IO_Type.TopCylinder_Down, IO_VALUE.HIGH);
} }
} }
internal void CloseCylinderStop() internal virtual void CloseCylinderStop()
{ {
if (baseConfig.DType.Equals(DeviceType.MoveEquip) || baseConfig.DType.Equals(DeviceType.ProvidingEquip)) if (baseConfig.DType.Equals(DeviceType.MoveEquip) || baseConfig.DType.Equals(DeviceType.ProvidingEquip))
{ {
...@@ -238,7 +238,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -238,7 +238,7 @@ namespace OnlineStore.DeviceLibrary
} }
string portName = axis.DeviceName; string portName = axis.DeviceName;
int slvAddr = axis.GetAxisValue(); int slvAddr = axis.GetAxisValue();
IOMove(IO_Type.BatchAxis_ServoOn, IO_VALUE.HIGH); IOMove(axis.ServerOnDO, IO_VALUE.HIGH);
Thread.Sleep(1000); Thread.Sleep(1000);
//打开所有轴 //打开所有轴
ACServerManager.OpenPort(portName); ACServerManager.OpenPort(portName);
...@@ -263,7 +263,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -263,7 +263,7 @@ namespace OnlineStore.DeviceLibrary
} }
} }
IsIntSlvBlock = true; IsIntSlvBlock = true;
IOMove(IO_Type.BatchAxis_BreakOn, IO_VALUE.HIGH); IOMove(axis.BreakOnDO, IO_VALUE.HIGH);
return true; return true;
} }
...@@ -314,14 +314,14 @@ namespace OnlineStore.DeviceLibrary ...@@ -314,14 +314,14 @@ namespace OnlineStore.DeviceLibrary
string portName = axis.DeviceName; string portName = axis.DeviceName;
int slvAddr = axis.GetAxisValue(); int slvAddr = axis.GetAxisValue();
LogUtil.info(Name + "关闭刹车，关闭伺服"); LogUtil.info(Name + "关闭刹车，关闭伺服");
IOMove(IO_Type.BatchAxis_BreakOn, IO_VALUE.LOW); IOMove(axis.BreakOnDO, IO_VALUE.LOW);
ACServerManager.ServoOff(portName, slvAddr); ACServerManager.ServoOff(portName, slvAddr);
//关闭串口，等下次重新打开 //关闭串口，等下次重新打开
ACServerManager.ColsePort(portName); ACServerManager.ColsePort(portName);
Thread.Sleep(100); Thread.Sleep(100);
IOMove(IO_Type.BatchAxis_ServoOn, IO_VALUE.LOW); IOMove(axis.ServerOnDO, IO_VALUE.LOW);
} }
...@@ -524,10 +524,10 @@ namespace OnlineStore.DeviceLibrary ...@@ -524,10 +524,10 @@ namespace OnlineStore.DeviceLibrary
int storeId = moveInfo.MoveParam.GetStoreId(); int storeId = moveInfo.MoveParam.GetStoreId();
wait.IsEnd = LineServer.BoxCanReviceTray(storeId); wait.IsEnd = LineServer.BoxCanReviceTray(storeId);
} }
else if (wait.WaitType.Equals(10)) //else if (wait.WaitType.Equals(10))
{ //{
wait.IsEnd = LineManager.Line.SideWay34HasTray().Equals(false); // wait.IsEnd = LineManager.Line.SideWay34HasTray().Equals(false);
} //}
if (wait.IsEnd && moveInfo.OneWaitCanEndStep) if (wait.IsEnd && moveInfo.OneWaitCanEndStep)
{ {
isOk = true; isOk = true;
...@@ -554,5 +554,20 @@ namespace OnlineStore.DeviceLibrary ...@@ -554,5 +554,20 @@ namespace OnlineStore.DeviceLibrary
} }
#endregion #endregion
protected void CheckLog(string msg)
{
LogUtil.debug(Name + msg);
}
protected void InStoreLog(string msg)
{
string posId = MoveInfo.MoveParam != null ? MoveInfo.MoveParam.PosId : "";
LogUtil.info(Name + "【" + posId + "】" + msg);
}
protected void OutStoreLog(string msg)
{
string posId = MoveInfo.MoveParam != null ? MoveInfo.MoveParam.PosId : "";
LogUtil.info(Name + "【" + posId + "】" + msg);
}
} }
} }
source/DeviceLibrary/assemblyLine/FeedingEquip.cs
...@@ -389,8 +389,58 @@ namespace OnlineStore.DeviceLibrary ...@@ -389,8 +389,58 @@ namespace OnlineStore.DeviceLibrary
{ {
} }
protected override void CheckFixtureProcess()
/// <summary>
/// 是否需要拦截当前托盘进行处理
/// </summary>
/// <returns></returns>
internal bool NeedCurrTray()
{
int num = TrayManager.GetNum(Config.Id);
bool isFull = TrayManager.IsFixTureFull(num);
if (Config.IsCanOut.Equals(1))
{
if (isFull && runStatus.Equals(LineRunStatus.Runing) && MoveInfo.MoveType.Equals(LineMoveType.OutStore))
{
return true;
}
}
else
{
if (!isFull && runStatus.Equals(LineRunStatus.Runing) && MoveInfo.MoveType.Equals(LineMoveType.InStore))
{ {
return true;
}
} }
return false;
} /// <summary>
/// 下降所有阻挡气缸
/// </summary>
internal override void OpenStopCylinder()
{
if (Config.SidesWayNum<=0)
{
LogInfo("下降阻挡气缸,下降顶升气缸 ");
IOMove(IO_Type.FL_StopCylinder_Down1, IO_VALUE.HIGH);
IOMove(IO_Type.FL_StopCylinder_Down2, IO_VALUE.HIGH);
//顶升气缸下降
IOMove(IO_Type.FL_TopCylinder_Up, IO_VALUE.LOW);
IOMove(IO_Type.FL_TopCylinder_Down, IO_VALUE.HIGH);
}
}
internal override void CloseCylinderStop()
{
if (Config.SidesWayNum <= 0)
{
LogInfo("上升阻挡气缸，关闭 顶升气缸IO");
IOMove(IO_Type.StopCylinder_Down1, IO_VALUE.LOW);
IOMove(IO_Type.StopCylinder_Down2, IO_VALUE.LOW);
//顶升气缸下降
IOMove(IO_Type.FL_TopCylinder_Up, IO_VALUE.LOW);
IOMove(IO_Type.FL_TopCylinder_Down, IO_VALUE.LOW);
}
}
} }
} }
source/DeviceLibrary/assemblyLine/FeedingEquip_Partial.cs
...@@ -10,6 +10,223 @@ namespace OnlineStore.DeviceLibrary ...@@ -10,6 +10,223 @@ namespace OnlineStore.DeviceLibrary
{ {
partial class FeedingEquip partial class FeedingEquip
{ {
#region 托盘检测
private void StartCheckFixture()
{
int num = TrayManager.GetNum(DeviceID);
if (IOValue(IO_Type.StopCylinder_Check2).Equals(IO_VALUE.HIGH))
{
//托盘在两个阻挡内
if (num > 0)
{
TrayManager.UpdateSWState(Config.SidesWayNum, 2);
SecondMoveInfo.NewMove(LineMoveType.CheckFixture);
CheckLog("托盘检测（流水线阻挡）SecondStoreMove：(MIO_03_StopCylinder2Down 阻挡气缸1-1上升）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_03_StopCylinder2Down);
IOMove(IO_Type.StopCylinder_Down1, IO_VALUE.LOW);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Down1, IO_VALUE.LOW));
}
else
{
LogUtil.error(Name + "检测到check4亮，但是为获取到托盘号，StartCheckFixture失败~");
}
}
else if (IOValue(IO_Type.StopCylinder_Check1).Equals(IO_VALUE.HIGH))
{
//托盘在第一个阻挡处
SecondMoveInfo.NewMove(LineMoveType.CheckFixture);
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_01_StopCylinder1Down);
TrayManager.UpdateSWState(Config.SidesWayNum, 2);
CheckLog(" 托盘检测：料盘检测 SecondStoreMove（MIO_01_StopCylinder1Down阻挡气缸1-1下降 ，最多等待1秒）");
IOMove(IO_Type.StopCylinder_Down1, IO_VALUE.HIGH);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Down1, IO_VALUE.HIGH));
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1500));
}
}
protected override void CheckFixtureProcess()
{
if (!LineManager.Line.LineCanRun())
{
return;
}
if (SecondMoveInfo.IsInWait)
{
CheckWait(SecondMoveInfo);
}
if (SecondMoveInfo.IsInWait)
{
return;
}
#region 托盘检测
if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MIO_01_StopCylinder1Down))
{
CheckLog("托盘检测（流水线阻挡）SecondStoreMove：(MIO_02_FixtureCheck 阻挡气缸1-1上升，等待 阻挡2托盘检测=1）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_03_StopCylinder2Down);
IOMove(IO_Type.StopCylinder_Down1, IO_VALUE.LOW);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Down1, IO_VALUE.LOW));
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Check2, IO_VALUE.HIGH));
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MIO_02_FixtureCheck))
{
CheckLog("托盘检测（流水线阻挡）SecondStoreMove：(MIO_03_StopCylinder2Down 阻挡气缸1-1上升）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_03_StopCylinder2Down);
IOMove(IO_Type.StopCylinder_Down1, IO_VALUE.LOW);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Down1, IO_VALUE.LOW));
// SecondMoveInfo.EndStepWait();
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MIO_03_StopCylinder2Down))
{
CheckLog("托盘检测（流水线阻挡）SecondStoreMove：(MIO_04_Wait ,等待编码信号稳定）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_04_Wait);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitTime(500));
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MIO_04_Wait))
{
try
{
//判断是否需要顶升
// bool isNeed = false;
//此处先对托盘号进行验证
currMoveTrayNum = TrayManager.GetNum(DeviceID);
bool isFull = TrayManager.IsFixTureFull(currMoveTrayNum);
if (TrayManager.RightTrayCode(currMoveTrayNum, preTrayNum, false))
{
//出料中，需要拦盘
if (NeedCurrTray())
{
//preTrayNum = currMoveTrayNum;
SecondMoveInfo.MoveParam = new InOutParam(currMoveTrayNum);
SecondMoveInfo.NextMoveStep(LineMoveStep.MO_05_CodeRember);
SecondMoveInfo.EndStepWait();
return;
}
}
else
{
string msg = Name + " 托盘顺序错乱，上个托盘号【" + preTrayNum + "】当前托盘号 【" + currMoveTrayNum + "】最大盘号【" + TrayManager.MaxTrayNum + "】";
TrayManager.UpdateTrayNumError(DeviceID, msg);
LogUtil.error(msg);
return;
}
LogInfo(SecondMoveInfo.MoveNum + "***************上个托盘号【" + preTrayNum + "】，当前" + (isFull ? "有料托盘" : "空托盘") + "【" + currMoveTrayNum + "】没有出入料任务，放盘通过~");
// preTrayNum = currMoveTrayNum;
if (TrayManager.ErrorStoreId.Equals(DeviceID))
{
TrayManager.UpdateTrayNumError(-1, "");
}
CheckLog("托盘放行 SecondStoreMove：(MO_07_WaitCanGo ，移栽2，需要判断是否可以放盘通过,最多等待10000）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MO_07_WaitCanGo);
}
catch (Exception ex)
{
LogUtil.error("判断托盘是否需要顶升出错：" + ex.ToString());
}
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MIO_05_WaitTime))
{
CheckLog("托盘检测（流水线阻挡）SecondStoreMove：(MIO_06_TopCylinderUp 顶升气缸上 升 ）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_06_TopCylinderUp);
CylinderMove(SecondMoveInfo, IO_Type.TopCylinder_Down, IO_Type.TopCylinder_UP);
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MIO_06_TopCylinderUp))
{
CheckLog("托盘检测（流水线阻挡）SecondStoreMove：(MIO_07_TopCylinderUpWait ,顶升气缸上升时等待1秒钟，再下降）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_07_TopCylinderUpWait);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MIO_07_TopCylinderUpWait))
{
CheckLog("托盘检测（流水线阻挡）*************** 托盘号【" + currMoveTrayNum + "】");
//托盘号正确
//preTrayNum = num;
//判断盘是空盘,空盘并且编号正确才需要放料盘过去
if (CheckIsNeedOutStore())
{
SecondMoveInfo.MoveParam = new InOutParam(currMoveTrayNum);
LogInfo(SecondMoveInfo.MoveNum + "*************** 托盘号【" + currMoveTrayNum + "】可以放出料托盘，正在出料中，移栽料盘");
SecondMoveInfo.NextMoveStep(LineMoveStep.MO_05_CodeRember);
SecondMoveInfo.EndStepWait();
}
else
{
//preTrayNum = num;
if (TrayManager.ErrorStoreId.Equals(DeviceID))
{
TrayManager.UpdateTrayNumError(-1, "");
}
CheckLog("托盘检测 SecondStoreMove：(MO_09_TopCylinder_Down ，托盘号【" + currMoveTrayNum + "】,直接放盘通过，顶升气缸下降）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MO_06_TopCylinder_Down);
CylinderMove(SecondMoveInfo, IO_Type.TopCylinder_UP, IO_Type.TopCylinder_Down);
}
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MIO_08_WaitInStore) && MoveInfo.MoveType.Equals(LineMoveType.None))
{
CheckLog("托盘放行 SecondStoreMove：(MIO_09_WaitLetFixtureGo ，等待移栽完成后放开阻挡）");
StartOutStoreMove(SecondMoveInfo.MoveParam);
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_09_WaitLetFixtureGo);
}
#endregion
#region 不需要出出料，直接放行
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MO_06_TopCylinder_Down))
{
CheckLog("托盘放行 SecondStoreMove：(MO_07_WaitCanGo ，移栽2，需要判断是否可以放盘通过,最多等待10000）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MO_07_WaitCanGo);
//更新横移托盘已处理完成
TrayManager.UpdateSWState(Config.SidesWayNum, 1);
//if (DeviceID.Equals(2))
//{
// SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitTime(10000));
// SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitSideWay());
// SecondMoveInfo.OneWaitCanEndStep = true;
//}
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MO_07_WaitCanGo))
{
CheckLog("托盘放行 SecondStoreMove：(MO_10_StopCylinder2_Down ，阻挡气缸1-2下降）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MO_10_StopCylinder2_Down);
IOMove(IO_Type.StopCylinder_Down2, IO_VALUE.HIGH);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Down2, IO_VALUE.HIGH));
// SecondMoveInfo.EndStepWait();
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MO_10_StopCylinder2_Down))
{
CheckLog("托盘放行 SecondStoreMove：(MO_11_Tray_Check ， 阻挡2托盘检测=0）, 延时2秒）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MO_11_Tray_Check);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Check2, IO_VALUE.LOW));
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MO_11_Tray_Check))
{
SecondMoveInfo.NextMoveStep(LineMoveStep.MO_12_StopCylinder_Back);
CheckLog("托盘放行 SecondStoreMove：(MO_12_StopCylinder_Back ， 阻挡气缸1-2上升 ）");
IOMove(IO_Type.StopCylinder_Down2, IO_VALUE.LOW);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Down2, IO_VALUE.LOW));
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitTime(200));
}
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MO_12_StopCylinder_Back))
{
preTrayNum = currMoveTrayNum;
CheckLog("托盘放行 SecondStoreMove：(托盘放行结束） ");
// IOMove(IO_Type.StopCylinder_Down1, IO_VALUE.HIGH);
SecondMoveInfo.EndMove();
}
#endregion
}
private bool CheckIsNeedOutStore()
{
throw new NotImplementedException();
}
#endregion
public override void StartInStoreMove(InOutParam param) public override void StartInStoreMove(InOutParam param)
{ {
throw new NotImplementedException(); throw new NotImplementedException();
......
source/DeviceLibrary/assemblyLine/LineBean.cs
...@@ -64,8 +64,8 @@ namespace OnlineStore.DeviceLibrary ...@@ -64,8 +64,8 @@ namespace OnlineStore.DeviceLibrary
baseConfig = lineConfig; baseConfig = lineConfig;
this.Config = lineConfig; this.Config = lineConfig;
this.DeviceID = lineConfig.Id; this.DeviceID = lineConfig.Id;
SW12_MoveInfo = new LineMoveInfo(DeviceID, "横移轨道-12"); SW41_MoveInfo = new LineMoveInfo(DeviceID, "横移轨道-41");
SW34_MoveInfo = new LineMoveInfo(DeviceID, "横移轨道-34"); SW23_MoveInfo = new LineMoveInfo(DeviceID, "横移轨道-23");
MoveInfo = new LineMoveInfo(DeviceID, "流水线-Move "); MoveInfo = new LineMoveInfo(DeviceID, "流水线-Move ");
Name = (" 流水线_" + Config.CID + " ").ToUpper(); Name = (" 流水线_" + Config.CID + " ").ToUpper();
...@@ -217,7 +217,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -217,7 +217,7 @@ namespace OnlineStore.DeviceLibrary
} }
private void RHomeOp() private void RHomeOp()
{ {
TrayManager.SidesWayStateMap = new Dictionary<int, int>();
alarmType = LineAlarmType.None; alarmType = LineAlarmType.None;
mainTimer.Enabled = false; mainTimer.Enabled = false;
IoCheckTimer.Enabled = false; IoCheckTimer.Enabled = false;
...@@ -227,7 +227,6 @@ namespace OnlineStore.DeviceLibrary ...@@ -227,7 +227,6 @@ namespace OnlineStore.DeviceLibrary
alarmType = LineAlarmType.None; alarmType = LineAlarmType.None;
TrayManager.TrayErrorMsg = ""; TrayManager.TrayErrorMsg = "";
WarnMsg = ""; WarnMsg = "";
preTrayNum = 0;
PreIsHasProcess = true; PreIsHasProcess = true;
if (TrayManager.ErrorStoreId > 0) if (TrayManager.ErrorStoreId > 0)
...@@ -244,8 +243,8 @@ namespace OnlineStore.DeviceLibrary ...@@ -244,8 +243,8 @@ namespace OnlineStore.DeviceLibrary
CylinderMove(null, IO_Type.NGCylinder_Before, IO_Type.NGCylinder_After); CylinderMove(null, IO_Type.NGCylinder_Before, IO_Type.NGCylinder_After);
////阻挡都上升 ////阻挡都上升
//IOMove(IO_Type.StopCylinder_Down1, IO_VALUE.LOW); //IOMove(IO_Type.FL_StopCylinder_Down1, IO_VALUE.LOW);
//IOMove(IO_Type.StopCylinder_Down2, IO_VALUE.LOW); //IOMove(IO_Type.FL_StopCylinder_Down2, IO_VALUE.LOW);
//横移轨道下降 //横移轨道下降
SideWayReset(); SideWayReset();
} }
...@@ -375,11 +374,11 @@ namespace OnlineStore.DeviceLibrary ...@@ -375,11 +374,11 @@ namespace OnlineStore.DeviceLibrary
{ {
return true; return true;
} }
if (SW12_MoveInfo.MoveType.Equals(LineMoveType.None).Equals(false)) if (SW41_MoveInfo.MoveType.Equals(LineMoveType.None).Equals(false))
{ {
return true; return true;
} }
if (SW34_MoveInfo.MoveType.Equals(LineMoveType.None).Equals(false)) if (SW23_MoveInfo.MoveType.Equals(LineMoveType.None).Equals(false))
{ {
return true; return true;
} }
...@@ -888,7 +887,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -888,7 +887,7 @@ namespace OnlineStore.DeviceLibrary
string wareNum = serverResult.barcode ; string wareNum = serverResult.barcode ;
int trayCode = TrayManager.GetNum(0); int trayCode = TrayManager.GetNum(0);
LogUtil.info( "更新盘空满信息，托盘号【" + trayCode + "】，是否有料盘【" + true + "】,出库入库【" + 1 + "】"); LogUtil.info( "更新盘空满信息，托盘号【" + trayCode + "】，是否有料盘【" + true + "】,出库入库【" + 1 + "】");
TrayManager.UpdateFixtureValue(trayCode, true, 1); TrayManager.UpdateFixtureValue(trayCode, true, 1,wareNum,posId,plateH,plateW);
//TODO:判断BOX是否处于可以入库状态，如果调试或急停中，需要返回给服务器； //TODO:判断BOX是否处于可以入库状态，如果调试或急停中，需要返回给服务器；
if (LineServer.BoxCanInStore(moveEquip.DeviceID)) if (LineServer.BoxCanInStore(moveEquip.DeviceID))
......
source/DeviceLibrary/assemblyLine/LineBean_Partial.cs
...@@ -10,17 +10,13 @@ namespace OnlineStore.DeviceLibrary ...@@ -10,17 +10,13 @@ namespace OnlineStore.DeviceLibrary
{ {
partial class LineBean partial class LineBean
{ {
/// <summary>
/// 上一个盘号
/// </summary>
private int preTrayNum = 0;
#region 定时处理方法 #region 定时处理方法
private DateTime NextScanTime = DateTime.Now; //private DateTime NextScanTime = DateTime.Now;
private DateTime NextEmptyGo = DateTime.Now; //private DateTime NextEmptyGo = DateTime.Now;
private bool IsWaitToScan = false; //private bool IsWaitToScan = false;
private bool IsWaitEmptyGo = false; //private bool IsWaitEmptyGo = false;
private bool isWaitOutGo = false; //private bool isWaitOutGo = false;
private DateTime WaitOutGoTime = DateTime.Now; //private DateTime WaitOutGoTime = DateTime.Now;
public bool LineCanRun() public bool LineCanRun()
...@@ -38,7 +34,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -38,7 +34,7 @@ namespace OnlineStore.DeviceLibrary
IOManager.IOValue(IO_Type.DriveMotor_Run1, 0).Equals(IO_VALUE.HIGH) && IOManager.IOValue(IO_Type.DriveMotor_Run1, 0).Equals(IO_VALUE.HIGH) &&
IOManager.IOValue(IO_Type.DriveMotor_Run2, 0).Equals(IO_VALUE.HIGH) && IOManager.IOValue(IO_Type.DriveMotor_Run2, 0).Equals(IO_VALUE.HIGH) &&
IOManager.IOValue(IO_Type.DriveMotor_Run3, 0).Equals(IO_VALUE.HIGH) && IOManager.IOValue(IO_Type.DriveMotor_Run3, 0).Equals(IO_VALUE.HIGH) &&
IOManager.IOValue(IO_Type.DriveMotor_Run4, 0).Equals(IO_VALUE.HIGH) ) IOManager.IOValue(IO_Type.DriveMotor_Run4, 0).Equals(IO_VALUE.HIGH))
{ {
if (isCheckSleep) if (isCheckSleep)
{ {
...@@ -69,12 +65,12 @@ namespace OnlineStore.DeviceLibrary ...@@ -69,12 +65,12 @@ namespace OnlineStore.DeviceLibrary
isInprocess = true; isInprocess = true;
lastProTime = DateTime.Now; lastProTime = DateTime.Now;
//出入料口条件： 各料仓无报警（ 伺服）， 各移栽装置处 于原位待机， 检测夹具IO，驱动电机运转 //出入料口条件： 各料仓无报警（ 伺服）， 各移栽装置处 于原位待机， 检测夹具IO，驱动电机运转
if (!CanProcessLine(false)) //if (!CanProcessLine(false))
{ //{
isWaitOutGo = false; // isWaitOutGo = false;
isInprocess = false; // isInprocess = false;
return; // return;
} //}
//if (IOValue(IO_Type.Fixture_Check_4).Equals(IO_VALUE.LOW)) //if (IOValue(IO_Type.Fixture_Check_4).Equals(IO_VALUE.LOW))
//{ //{
...@@ -248,7 +244,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -248,7 +244,7 @@ namespace OnlineStore.DeviceLibrary
} }
//若BOX和移栽都没有在等待Io的过程中则此Io超时异常可能已经处理过 //若BOX和移栽都没有在等待Io的过程中则此Io超时异常可能已经处理过
if (MoveInfo.IsInWait.Equals(false) && SW12_MoveInfo.IsInWait.Equals(false) && SW34_MoveInfo.IsInWait.Equals(false)) if (MoveInfo.IsInWait.Equals(false) && SW41_MoveInfo.IsInWait.Equals(false) && SW23_MoveInfo.IsInWait.Equals(false))
{ {
LogUtil.info(Name + "清理信号超时报警【" + WarnMsg + "】 "); LogUtil.info(Name + "清理信号超时报警【" + WarnMsg + "】 ");
alarmType = LineAlarmType.None; alarmType = LineAlarmType.None;
...@@ -538,85 +534,56 @@ namespace OnlineStore.DeviceLibrary ...@@ -538,85 +534,56 @@ namespace OnlineStore.DeviceLibrary
#region 横移处理 #region 横移处理
private static LineMoveInfo SW12_MoveInfo = null; private static LineMoveInfo SW41_MoveInfo = null;
private static LineMoveInfo SW34_MoveInfo = null; private static LineMoveInfo SW23_MoveInfo = null;
private bool SideWayReset() private bool SideWayReset()
{ {
SideWayStop(); SideWayStop();
CylinderMove(null, IO_Type.SW1_TopCylinder_Up, IO_Type.SW1_TopCylinder_Down);
SideWay12TopCylinderMove(IO_VALUE.HIGH, IO_VALUE.LOW, null); CylinderMove(null, IO_Type.SW1_TopCylinder_Up, IO_Type.SW1_TopCylinder_Down);
SideWay34TopCylinderMove(IO_VALUE.HIGH, IO_VALUE.LOW, null); CylinderMove(null, IO_Type.SW4_TopCylinder_Up, IO_Type.SW4_TopCylinder_Down);
CylinderMove(null, IO_Type.SW1_LocationCylinder_Up, IO_Type.SW1_LocationCylinder_Down);
CylinderMove(null, IO_Type.SW4_LocationCylinder_Up, IO_Type.SW4_LocationCylinder_Down);
return true; return true;
} }
private void SideWayStop() private void SideWayStop()
{ {
SideWay12IsWait = false; SideWay41IsWait = false;
SideWay34IsWait = false; SideWay23IsWait = false;
SW12_MoveInfo.EndMove(); SW41_MoveInfo.EndMove();
SW34_MoveInfo.EndMove(); SW23_MoveInfo.EndMove();
//IOMove(IO_Type.SidesWay12_DriveMotor, IO_VALUE.LOW); IOMove(IO_Type.SW1_MotorRun, IO_VALUE.LOW);
//IOMove(IO_Type.SidesWay34_DriveMotor, IO_VALUE.LOW); IOMove(IO_Type.SW2_MotorRun, IO_VALUE.LOW);
IOMove(IO_Type.SW3_MotorRun, IO_VALUE.LOW);
IOMove(IO_Type.SW4_MotorRun, IO_VALUE.LOW);
////阻挡气缸先上升
//IOMove(IO_Type.SidesWay1_StopCylinderDown, IO_VALUE.LOW);
//IOMove(IO_Type.SidesWay3_StopCylinderDown, IO_VALUE.LOW);
} }
public void SideWay12TopCylinderMove(IO_VALUE downValue, IO_VALUE upValue, LineMoveInfo moveInfo = null) ///// <summary>
{ ///// 判断横移轨道23是否有托盘
//IOMove(IO_Type.SidesWay12_TopCylinder_Down, downValue); ///// </summary>
//IOMove(IO_Type.SidesWay12_TopCylinder_Up, upValue); ///// <returns></returns>
//public bool SideWay23HasTray()
//if (moveInfo != null)
//{
// moveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay1_TopCylinder_Down, downValue));
// moveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay1_TopCylinder_Up, upValue));
// moveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay2_TopCylinder_Down, downValue));
// moveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay2_TopCylinder_Up, upValue));
// moveInfo.WriteIoList.Add(WriteIOInfo.NInfo(IO_Type.SidesWay12_TopCylinder_Down, downValue));
// moveInfo.WriteIoList.Add(WriteIOInfo.NInfo(IO_Type.SidesWay12_TopCylinder_Up, upValue));
//}
}
public void SideWay34TopCylinderMove(IO_VALUE downValue, IO_VALUE upValue, LineMoveInfo moveInfo = null)
{
//IOMove(IO_Type.SidesWay34_TopCylinder_Down, downValue);
//IOMove(IO_Type.SidesWay34_TopCylinder_Up, upValue);
//if (moveInfo != null)
//{
// moveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay3_TopCylinder_Down, downValue));
// moveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay3_TopCylinder_Up, upValue));
// moveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay4_TopCylinder_Down, downValue));
// moveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay4_TopCylinder_Up, upValue));
// moveInfo.WriteIoList.Add(WriteIOInfo.NInfo(IO_Type.SidesWay34_TopCylinder_Down, downValue));
// moveInfo.WriteIoList.Add(WriteIOInfo.NInfo(IO_Type.SidesWay34_TopCylinder_Up, upValue));
//}
}
/// <summary>
/// 判断横移轨道34是否有托盘
/// </summary>
/// <returns></returns>
public bool SideWay34HasTray()
{
////正在横移中，且托盘顶升气缸未下降
//if (SW34_MoveInfo.MoveType.Equals(LineMoveType.None).Equals(false) && SW34_MoveInfo.MoveStep <= LineMoveStep.SW07_TopCylinderDown)
//{ //{
// //正在横移中，且托盘顶升气缸未下降
// if (SW23_MoveInfo.MoveType.Equals(LineMoveType.None).Equals(false) && SW23_MoveInfo.MoveStep <= LineMoveStep.SW07_TopCylinderDown)
// {
// return true; // return true;
//} // }
//if (IOValue(IO_Type.SidesWay3_FixtureCheck).Equals(IO_VALUE.HIGH)) // if (IOValue(IO_Type.SW2_TrayCheck).Equals(IO_VALUE.HIGH)&&IOValue(IO_Type.SW3_TrayCheck).Equals(IO_VALUE.LOW))
//{ // {
// return true; // return true;
// }
// return false;
//} //}
return false; private DateTime SideWay41Ntime = DateTime.Now;
} private bool SideWay41IsWait = false;
private DateTime SideWay12Ntime = DateTime.Now; private DateTime SideWay23Ntime = DateTime.Now;
private bool SideWay12IsWait = false; private bool SideWay23IsWait = false;
private DateTime SideWay34Ntime = DateTime.Now;
private bool SideWay34IsWait = false;
private bool sdIsInprocess = false; private bool sdIsInprocess = false;
...@@ -631,93 +598,93 @@ namespace OnlineStore.DeviceLibrary ...@@ -631,93 +598,93 @@ namespace OnlineStore.DeviceLibrary
try try
{ {
sdIsInprocess = true; sdlastProTime = DateTime.Now; sdIsInprocess = true; sdlastProTime = DateTime.Now;
////流水线转动中，并且在忙碌或出入库处理中，需要处理移栽 //流水线转动中，并且在忙碌或出入库处理中，需要处理移栽
//if (IOValue(IO_Type.DriveMotor_Run).Equals(IO_VALUE.HIGH) && runStatus >= LineRunStatus.Runing) if (!CanProcessLine())
//{ {
// if (SW12_MoveInfo.MoveType.Equals(LineMoveType.None) && IOValue(IO_Type.SidesWay2_FixtureCheck).Equals(IO_VALUE.LOW)) SideWay23IsWait = false;
// { SideWay41IsWait = false;
// TimeSpan span12 = DateTime.Now - SideWay12Ntime; sdIsInprocess = false;
// //检测到阻挡夹具信号后，阻挡气缸下降，等待有夹具信号，阻挡气缸上升， return;
// //顶升气缸上升到位，开始流水线转动，检测到出口信号后，停止转动，顶升气缸下降，阻挡2下降，盘通过 }
// if (IOValue(IO_Type.SidesWay1_StopFixtureCheck).Equals(IO_VALUE.HIGH)) if (SW41_MoveInfo.MoveType.Equals(LineMoveType.None))
// { {
// if (SideWay12IsWait && span12.TotalSeconds > 1)
// {
// SWLog("横移轨道阻挡1检测到托盘，开始移动托盘，下降横移气缸12"); if (IOValue(IO_Type.SW4_TrayCheck).Equals(IO_VALUE.HIGH) && IOValue(IO_Type.SW1_TrayCheck).Equals(IO_VALUE.LOW)&&
// SW12_MoveInfo.NewMove(LineMoveType.InStore); TrayManager.CanMoveSidesWay(4)&&TrayManager.CanMoveSidesWay(1))
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW00_Wait); {
// SideWay12TopCylinderMove(IO_VALUE.HIGH, IO_VALUE.LOW, SW12_MoveInfo); TimeSpan span12 = DateTime.Now - SideWay41Ntime;
// } if (SideWay41IsWait && span12.TotalSeconds > 1)
// else if (!SideWay12IsWait) {
// { SWLog("横移轨道4检测到托盘，定位气缸下降");
// SideWay12IsWait = true; SW41_MoveInfo.NewMove(LineMoveType.InStore);
// SideWay12Ntime = DateTime.Now; SW41_MoveInfo.NextMoveStep(LineMoveStep.SW01_LocationCylinderDown);
// } //IOMove(IO_Type.SW1_StopCylinderDown, IO_VALUE.LOW);
// } // SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW4_TrayCheck, IO_VALUE.HIGH));
// else if (IOValue(IO_Type.SidesWay1_FixtureCheck).Equals(IO_VALUE.HIGH)) //CylinderMove(SW41_MoveInfo, IO_Type.SW1_TopCylinder_Up, IO_Type.SW1_TopCylinder_Down);
// { //CylinderMove(SW41_MoveInfo, IO_Type.SW4_TopCylinder_Up, IO_Type.SW4_TopCylinder_Down);
// if (SideWay12IsWait && span12.TotalSeconds > 1)
// { CylinderMove(SW41_MoveInfo, IO_Type.SW1_LocationCylinder_Up, IO_Type.SW1_LocationCylinder_Down);
// SWLog("横移轨道1检测到托盘，阻挡1上升，等待横移1夹具检测信号"); CylinderMove(SW41_MoveInfo, IO_Type.SW4_LocationCylinder_Up, IO_Type.SW4_LocationCylinder_Down);
// SW12_MoveInfo.NewMove(LineMoveType.InStore);
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW02_WaitFixtureCheck); }
// IOMove(IO_Type.SidesWay1_StopCylinderDown, IO_VALUE.LOW); else if (!SideWay41IsWait)
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay1_FixtureCheck, IO_VALUE.HIGH)); {
// } SideWay41IsWait = true;
// else if (!SideWay12IsWait) SideWay41Ntime = DateTime.Now;
// { }
// SideWay12IsWait = true; }
// SideWay12Ntime = DateTime.Now; else
// } {
// } SideWay41IsWait = false;
// else }
// { }
// SideWay12IsWait = false; else
// } {
// } SideWay41IsWait = false;
// else SideWay41BusyProcess();
// { }
// SideWay12IsWait = false;
// SideWay12BusyProcess(); if (SW23_MoveInfo.MoveType.Equals(LineMoveType.None))
// } {
//检测到阻挡夹具信号后，阻挡气缸下降，等待有夹具信号，阻挡气缸上升，
//顶升气缸上升到位，开始流水线转动，检测到出口信号后，停止转动，顶升气缸下降，阻挡4下降，盘通过
if (IOValue(IO_Type.SW2_TrayCheck).Equals(IO_VALUE.HIGH) && IOValue(IO_Type.SW3_TrayCheck).Equals(IO_VALUE.LOW) &&
TrayManager.CanMoveSidesWay(2) && TrayManager.CanMoveSidesWay(3))
{
TimeSpan span34 = DateTime.Now - SideWay23Ntime;
if (SideWay23IsWait && span34.TotalSeconds > 1)
{
SWLog("横移轨道2检测到托盘，定位气缸下降");
SW23_MoveInfo.NewMove(LineMoveType.InStore);
SW23_MoveInfo.NextMoveStep(LineMoveStep.SW01_LocationCylinderDown);
//IOMove(IO_Type.SW3_StopCylinderDown, IO_VALUE.HIGH);
//SideWay23TopCylinderMove(IO_VALUE.HIGH, IO_VALUE.LOW, SW23_MoveInfo);
// SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW2_TrayCheck, IO_VALUE.HIGH));
//CylinderMove(SW23_MoveInfo, IO_Type.SW2_TopCylinder_Up, IO_Type.SW2_TopCylinder_Down);
//CylinderMove(SW23_MoveInfo, IO_Type.SW3_TopCylinder_Up, IO_Type.SW3_TopCylinder_Down);
CylinderMove(SW23_MoveInfo, IO_Type.SW2_LocationCylinder_Up, IO_Type.SW2_LocationCylinder_Down);
CylinderMove(SW23_MoveInfo, IO_Type.SW3_LocationCylinder_Up, IO_Type.SW3_LocationCylinder_Down);
}
else if (!SideWay23IsWait)
{
SideWay23IsWait = true;
SideWay23Ntime = DateTime.Now;
}
}
else
{
SideWay23IsWait = false;
}
}
else
{
SideWay23IsWait = false;
SideWay23BusyProcess();
}
// if (SW34_MoveInfo.MoveType.Equals(LineMoveType.None) && IOValue(IO_Type.SidesWay4_FixtureCheck).Equals(IO_VALUE.LOW))
// {
// TimeSpan span34 = DateTime.Now - SideWay34Ntime;
// //检测到阻挡夹具信号后，阻挡气缸下降，等待有夹具信号，阻挡气缸上升，
// //顶升气缸上升到位，开始流水线转动，检测到出口信号后，停止转动，顶升气缸下降，阻挡4下降，盘通过
// if (IOValue(IO_Type.SidesWay3_FixtureCheck).Equals(IO_VALUE.HIGH))
// {
// if (SideWay34IsWait && span34.TotalSeconds > 1)
// {
// SWLog("横移轨道3检测到托盘，开始移动托盘");
// SW34_MoveInfo.NewMove(LineMoveType.InStore);
// SW34_MoveInfo.NextMoveStep(LineMoveStep.SW01_StopCylinderDown);
// IOMove(IO_Type.SidesWay3_StopCylinderDown, IO_VALUE.HIGH);
// SideWay34TopCylinderMove(IO_VALUE.HIGH, IO_VALUE.LOW, SW34_MoveInfo);
// }
// else if (!SideWay34IsWait)
// {
// SideWay34IsWait = true;
// SideWay34Ntime = DateTime.Now;
// }
// }
// else
// {
// SideWay34IsWait = false;
// }
// }
// else
// {
// SideWay34IsWait = false;
// SideWay34BusyProcess();
// }
//}
//else
//{
// SideWay34IsWait = false;
// SideWay12IsWait = false;
//}
} }
catch (Exception ex) catch (Exception ex)
{ {
...@@ -726,167 +693,210 @@ namespace OnlineStore.DeviceLibrary ...@@ -726,167 +693,210 @@ namespace OnlineStore.DeviceLibrary
sdIsInprocess = false; sdIsInprocess = false;
} }
private void SideWay12BusyProcess() private void SideWay41BusyProcess()
{ {
if (SW12_MoveInfo.IsInWait) if (SW41_MoveInfo.IsInWait)
{ {
CheckWait(SW12_MoveInfo); CheckWait(SW41_MoveInfo);
} }
if (SW12_MoveInfo.IsInWait) if (SW41_MoveInfo.IsInWait)
{ {
return; return;
} }
//if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW00_Wait)) if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW01_LocationCylinderDown))
//{ {
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW01_StopCylinderDown); SW41_MoveInfo.NextMoveStep(LineMoveStep.SW02_WaitFixtureCheck);
// SWLog("横移轨道12：阻挡1下降，最多下降1000 "); SWLog("横移轨道41： 等待横移4托盘检测信号 ");
// IOMove(IO_Type.SidesWay1_StopCylinderDown, IO_VALUE.HIGH); SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW4_TrayCheck, IO_VALUE.HIGH));
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000)); }
//} else if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW02_WaitFixtureCheck))
//else if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW01_StopCylinderDown)) {
//{ SW41_MoveInfo.NextMoveStep(LineMoveStep.SW03_TopCylinderUp);
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW02_WaitFixtureCheck); SWLog("横移轨道41：顶升气缸上升 ,至少等待1000 ");
// SWLog("横移轨道12：阻挡1上升，等待横移1夹具检测信号 "); SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
// IOMove(IO_Type.SidesWay1_StopCylinderDown, IO_VALUE.LOW); CylinderMove(SW23_MoveInfo, IO_Type.SW4_TopCylinder_Down, IO_Type.SW4_TopCylinder_Up);
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay1_FixtureCheck, IO_VALUE.HIGH)); CylinderMove(SW23_MoveInfo, IO_Type.SW1_TopCylinder_Down, IO_Type.SW1_TopCylinder_Up);
//}
//else if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW02_WaitFixtureCheck))
//{
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW03_TopCylinderUp);
// SWLog("横移轨道12：顶升气缸上升 ,横移1阻挡上升 ,至少等待1000 ");
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
// IOMove(IO_Type.SidesWay1_StopCylinderDown, IO_VALUE.LOW);
// SideWay12TopCylinderMove(IO_VALUE.LOW, IO_VALUE.HIGH, SW12_MoveInfo);
//}
//else if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW03_TopCylinderUp))
//{
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW04_DriveMotorMove);
// SWLog("横移轨道12：开始转动电机 ,等待1000，等待SidesWay2_FixtureCheck=1, SidesWay1_FixtureCheck=0 ");
// IOMove(IO_Type.SidesWay12_DriveMotor, IO_VALUE.HIGH);
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay2_FixtureCheck, IO_VALUE.HIGH));
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay1_FixtureCheck, IO_VALUE.LOW));
//}
//else if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW04_DriveMotorMove))
//{
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW05_WaitOutFixtureCheck);
// SWLog("横移轨道12：等待托盘到达出口 ");
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(2000));
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay2_FixtureCheck, IO_VALUE.HIGH));
//}
//else if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW05_WaitOutFixtureCheck))
//{
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW06_WatOutFixture2);
// SWLog("横移轨道12：再次验证托盘是否在出口处 ");
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay2_FixtureCheck, IO_VALUE.HIGH));
//} }
//else if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW06_WatOutFixture2)) else if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW03_TopCylinderUp))
//{ {
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW07_TopCylinderDown); SW41_MoveInfo.NextMoveStep(LineMoveStep.SW04_DriveMotorMove);
// SWLog("横移轨道12：托盘已到达出口，顶升气缸下降 "); SWLog("横移轨道41：开始转动电机 ,等待1000，SW4_TrayCheck=0, SW1_TrayCheck=1 ");
// SideWay12TopCylinderMove(IO_VALUE.HIGH, IO_VALUE.LOW, SW12_MoveInfo); IOMove(IO_Type.SW4_MotorRun, IO_VALUE.HIGH);
//} IOMove(IO_Type.SW1_MotorRun, IO_VALUE.HIGH);
//else if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW07_TopCylinderDown)) SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
//{ SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW1_TrayCheck, IO_VALUE.HIGH));
// SW12_MoveInfo.NextMoveStep(LineMoveStep.SW09_WaitTrayGo); SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW4_TrayCheck, IO_VALUE.LOW));
// SWLog("横移轨道12：等待SidesWay2_FixtureCheck=0，最多等待5秒，关闭横移电机 "); }
// IOMove(IO_Type.SidesWay12_DriveMotor, IO_VALUE.LOW); else if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW04_DriveMotorMove))
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay2_FixtureCheck, IO_VALUE.LOW)); {
// SW12_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(5000)); SW41_MoveInfo.NextMoveStep(LineMoveStep.SW05_WaitOutFixtureCheck);
// SW12_MoveInfo.OneWaitCanEndStep = true; SWLog("横移轨道41：等待托盘到达出口 ");
//} SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(800));
//else if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW08_StopDrive)) SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW1_TrayCheck, IO_VALUE.HIGH));
//{ }
else if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW05_WaitOutFixtureCheck))
{
SW41_MoveInfo.NextMoveStep(LineMoveStep.SW06_WatOutFixture2);
SWLog("横移轨道41：再次验证托盘是否在出口处 ");
SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(500));
SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW1_TrayCheck, IO_VALUE.HIGH));
//}
//else if (SW12_MoveInfo.MoveStep.Equals(LineMoveStep.SW09_WaitTrayGo))
//{
// SW12_MoveInfo.EndMove();
// SWLog("横移轨道12：横移结束 ");
//}
} }
else if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW06_WatOutFixture2))
{
SW41_MoveInfo.NextMoveStep(LineMoveStep.SW07_TopCylinderDown);
SWLog("横移轨道41：托盘已到达出口，顶升气缸下降，判断入料1是否需要此托盘 ");
CylinderMove(SW41_MoveInfo, IO_Type.SW4_TopCylinder_Up, IO_Type.SW4_TopCylinder_Down);
if (!CheckTrayIsNeed(101))
{
CylinderMove(SW41_MoveInfo, IO_Type.SW1_TopCylinder_Up, IO_Type.SW1_TopCylinder_Down);
}
}
else if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW07_TopCylinderDown))
{
if (CheckTrayIsNeed(101))
{
SW41_MoveInfo.NextMoveStep(LineMoveStep.SW09_WaitTrayGo);
SWLog("横移轨道41：关闭皮带电机，不需要等待 托盘离开");
IOMove(IO_Type.SW4_MotorRun, IO_VALUE.LOW);
IOMove(IO_Type.SW1_MotorRun, IO_VALUE.LOW);
SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW4_MotorRun, IO_VALUE.LOW));
SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW1_MotorRun, IO_VALUE.LOW));
}
else
{
SW41_MoveInfo.NextMoveStep(LineMoveStep.SW09_WaitTrayGo);
SWLog("横移轨道41：关闭皮带电机，等待SW1_TrayCheck=0，最多等待5秒，关闭横移电机 ");
IOMove(IO_Type.SW4_MotorRun, IO_VALUE.LOW);
IOMove(IO_Type.SW1_MotorRun, IO_VALUE.LOW);
SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW1_TrayCheck, IO_VALUE.LOW));
SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(5000));
SW41_MoveInfo.OneWaitCanEndStep = true;
}
}
else if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW08_StopDrive))
{
private void SideWay34BusyProcess() }
else if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW09_WaitTrayGo))
{ {
if (SW34_MoveInfo.IsInWait) SW41_MoveInfo.EndMove();
SWLog("横移轨道41：横移结束 ");
TrayManager.UpdateSWState(4, 0);
TrayManager.UpdateSWState(1, 0);
}
}
private bool CheckTrayIsNeed(int deviceId)
{ {
CheckWait(SW34_MoveInfo); //横移1对应入料1
if (FeedingEquipMap.ContainsKey(deviceId))
{
FeedingEquip equip = FeedingEquipMap[deviceId];
if (equip.runStatus >= LineRunStatus.Runing)
{
if (equip.NeedCurrTray())
{
return true;
}
} }
if (SW34_MoveInfo.IsInWait) }
return false;
}
private void SideWay23BusyProcess()
{
if (SW23_MoveInfo.IsInWait)
{
CheckWait(SW23_MoveInfo);
}
if (SW23_MoveInfo.IsInWait)
{ {
return; return;
} }
//if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW00_Wait)) if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW01_LocationCylinderDown))
//{ {
// SW34_MoveInfo.NextMoveStep(LineMoveStep.SW01_StopCylinderDown); SW23_MoveInfo.NextMoveStep(LineMoveStep.SW02_WaitFixtureCheck);
// SWLog("横移轨道34：阻挡3下降，最多下降1000 "); SWLog("横移轨道23： 等待横移4托盘检测信号 ");
// IOMove(IO_Type.SidesWay3_StopCylinderDown, IO_VALUE.HIGH); SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW2_TrayCheck, IO_VALUE.HIGH));
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000)); }
//} else if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW02_WaitFixtureCheck))
//else if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW01_StopCylinderDown)) {
//{ SW23_MoveInfo.NextMoveStep(LineMoveStep.SW03_TopCylinderUp);
// SW34_MoveInfo.NextMoveStep(LineMoveStep.SW02_WaitFixtureCheck); SWLog("横移轨道23：顶升气缸上升 ,至少等待1000 ");
// SWLog("横移轨道34：横移3阻挡上升，等待横移3夹具检测信号 "); SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
// IOMove(IO_Type.SidesWay3_StopCylinderDown, IO_VALUE.LOW); CylinderMove(SW23_MoveInfo, IO_Type.SW2_TopCylinder_Down, IO_Type.SW2_TopCylinder_Up);
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay3_FixtureCheck, IO_VALUE.HIGH)); CylinderMove(SW23_MoveInfo, IO_Type.SW3_TopCylinder_Down, IO_Type.SW3_TopCylinder_Up);
//}
//else if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW02_WaitFixtureCheck))
//{
// SW34_MoveInfo.NextMoveStep(LineMoveStep.SW03_TopCylinderUp);
// SWLog("横移轨道34：顶升气缸上升 ,横移3阻挡上升,至少等待1000 ");
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
// IOMove(IO_Type.SidesWay3_StopCylinderDown, IO_VALUE.LOW);
// SideWay34TopCylinderMove(IO_VALUE.LOW, IO_VALUE.HIGH, SW34_MoveInfo);
//}
//else if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW03_TopCylinderUp))
//{
// SW34_MoveInfo.NextMoveStep(LineMoveStep.SW04_DriveMotorMove);
// SWLog("横移轨道34：开始转动电机 ，等待1000 ，等待SidesWay4_FixtureCheck=1 ,SidesWay3_FixtureCheck=0 ");
// IOMove(IO_Type.SidesWay34_DriveMotor, IO_VALUE.HIGH);
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay4_FixtureCheck, IO_VALUE.HIGH));
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay3_FixtureCheck, IO_VALUE.LOW));
//}
//else if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW04_DriveMotorMove))
//{
// SW34_MoveInfo.NextMoveStep(LineMoveStep.SW05_WaitOutFixtureCheck);
// SWLog("横移轨道34：等待托盘到达出口 ");
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(2000));
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay4_FixtureCheck, IO_VALUE.HIGH));
//}
//else if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW05_WaitOutFixtureCheck))
//{
// SW34_MoveInfo.NextMoveStep(LineMoveStep.SW06_WatOutFixture2);
// SWLog("横移轨道34：再次验证托盘是否到达出口 ");
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay4_FixtureCheck, IO_VALUE.HIGH));
//}
//else if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW06_WatOutFixture2))
//{
// SW34_MoveInfo.NextMoveStep(LineMoveStep.SW07_TopCylinderDown);
// SWLog("横移轨道34：托盘已到达出口，顶升气缸下降 ");
// SideWay34TopCylinderMove(IO_VALUE.HIGH, IO_VALUE.LOW, SW34_MoveInfo);
//}
//else if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW07_TopCylinderDown))
//{
// SW34_MoveInfo.NextMoveStep(LineMoveStep.SW09_WaitTrayGo);
// SWLog("横移轨道34：等待SidesWay4_FixtureCheck=0 ,最多等待5秒，关闭横移电机 ");
// IOMove(IO_Type.SidesWay34_DriveMotor, IO_VALUE.LOW);
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SidesWay4_FixtureCheck, IO_VALUE.LOW));
// SW34_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(5000));
// SW34_MoveInfo.OneWaitCanEndStep = true;
//}
//else if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW08_StopDrive))
//{
//} }
//else if (SW34_MoveInfo.MoveStep.Equals(LineMoveStep.SW09_WaitTrayGo)) else if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW03_TopCylinderUp))
//{ {
// SW34_MoveInfo.EndMove(); SW23_MoveInfo.NextMoveStep(LineMoveStep.SW04_DriveMotorMove);
// SWLog("横移轨道34：横移结束 "); SWLog("横移轨道23：开始转动电机 ,等待1000，SW2_TrayCheck=0, SW3_TrayCheck=1 ");
//} IOMove(IO_Type.SW2_MotorRun, IO_VALUE.HIGH);
IOMove(IO_Type.SW3_MotorRun, IO_VALUE.HIGH);
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW3_TrayCheck, IO_VALUE.HIGH));
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW2_TrayCheck, IO_VALUE.LOW));
}
else if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW04_DriveMotorMove))
{
SW23_MoveInfo.NextMoveStep(LineMoveStep.SW05_WaitOutFixtureCheck);
SWLog("横移轨道23：等待托盘到达出口 ");
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(800));
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW3_TrayCheck, IO_VALUE.HIGH));
}
else if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW05_WaitOutFixtureCheck))
{
SW23_MoveInfo.NextMoveStep(LineMoveStep.SW06_WatOutFixture2);
SWLog("横移轨道23：再次验证托盘是否在出口处 ");
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(500));
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW3_TrayCheck, IO_VALUE.HIGH));
}
else if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW06_WatOutFixture2))
{
SW23_MoveInfo.NextMoveStep(LineMoveStep.SW07_TopCylinderDown);
SWLog("横移轨道23：托盘已到达出口，顶升气缸下降 ");
CylinderMove(SW23_MoveInfo, IO_Type.SW2_TopCylinder_Up, IO_Type.SW2_TopCylinder_Down);
if (!CheckTrayIsNeed(104))
{
CylinderMove(SW23_MoveInfo, IO_Type.SW3_TopCylinder_Up, IO_Type.SW3_TopCylinder_Down);
}
}
else if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW07_TopCylinderDown))
{
if (CheckTrayIsNeed(104))
{
SW23_MoveInfo.NextMoveStep(LineMoveStep.SW09_WaitTrayGo);
SWLog("横移轨道41：关闭皮带电机，不需要等待 托盘离开");
IOMove(IO_Type.SW2_MotorRun, IO_VALUE.LOW);
IOMove(IO_Type.SW3_MotorRun, IO_VALUE.LOW);
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW2_MotorRun, IO_VALUE.LOW));
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW3_MotorRun, IO_VALUE.LOW));
}
else
{
SW23_MoveInfo.NextMoveStep(LineMoveStep.SW09_WaitTrayGo);
SWLog("横移轨道23：关闭皮带电机，等待SW3_TrayCheck=0，最多等待5秒，关闭横移电机 ");
IOMove(IO_Type.SW2_MotorRun, IO_VALUE.LOW);
IOMove(IO_Type.SW3_MotorRun, IO_VALUE.LOW);
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW3_TrayCheck, IO_VALUE.LOW));
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(5000));
SW23_MoveInfo.OneWaitCanEndStep = true;
}
}
else if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW08_StopDrive))
{
}
else if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW09_WaitTrayGo))
{
SW23_MoveInfo.EndMove();
SWLog("横移轨道23：横移结束 ");
TrayManager.UpdateSWState(2, 0);
TrayManager.UpdateSWState(3, 0);
}
} }
private void SWLog(string msg) private void SWLog(string msg)
......
source/DeviceLibrary/assemblyLine/MoveEquip.cs
...@@ -39,6 +39,9 @@ namespace OnlineStore.DeviceLibrary ...@@ -39,6 +39,9 @@ namespace OnlineStore.DeviceLibrary
Config.UpDown_Axis.HomeAddSpeed = Config.UpdownAxis_HomeAddSpeed; Config.UpDown_Axis.HomeAddSpeed = Config.UpdownAxis_HomeAddSpeed;
Config.UpDown_Axis.HomeHighSpeed = Config.UpdownAxis_HomeHighSpeed; Config.UpDown_Axis.HomeHighSpeed = Config.UpdownAxis_HomeHighSpeed;
Config.UpDown_Axis.HomeLowSpeed = Config.UpdownAxis_HomeLowSpeed; Config.UpDown_Axis.HomeLowSpeed = Config.UpdownAxis_HomeLowSpeed;
Config.UpDown_Axis.ServerOnDO = IO_Type.UpDownAxis_ServoOn;
Config.UpDown_Axis.BreakOnDO = IO_Type.UpDownAxis_BreakOn;
} }
} }
...@@ -187,11 +190,11 @@ namespace OnlineStore.DeviceLibrary ...@@ -187,11 +190,11 @@ namespace OnlineStore.DeviceLibrary
runStatus = LineRunStatus.Reset; runStatus = LineRunStatus.Reset;
SecondMoveInfo.EndMove(); SecondMoveInfo.EndMove();
MoveInfo.NewMove(LineMoveType.Reset); MoveInfo.NewMove(LineMoveType.Reset);
UpDownStartReset(); StartReset();
return true; return true;
} }
private void UpDownStartReset() private void StartReset()
{ {
//移载装置原点状态：顶升气缸下降端，前后气缸后退端，上下气缸上升端，夹料气缸放松端，阻挡气缸输入=0 //移载装置原点状态：顶升气缸下降端，前后气缸后退端，上下气缸上升端，夹料气缸放松端，阻挡气缸输入=0
UpdownHomeMove(); UpdownHomeMove();
......
source/DeviceLibrary/assemblyLine/MoveEquip_Partial.cs
...@@ -141,17 +141,10 @@ namespace OnlineStore.DeviceLibrary ...@@ -141,17 +141,10 @@ namespace OnlineStore.DeviceLibrary
{ {
OutStoreLog("出库：(MO_07_ClampCylinderTighten 夹料气缸1放松 ）"); OutStoreLog("出库：(MO_07_ClampCylinderTighten 夹料气缸1放松 ）");
int bagWidth = MoveInfo.MoveParam.PlateW; int bagWidth = MoveInfo.MoveParam.PlateW;
if (MoveInfo.MoveParam != null)
{
LogInfo("【" + posId + "】出库时，更新盘空满信息 托盘号【" + MoveInfo.MoveParam.TrayNumber + "】，是否有料盘【" + true + "】,出库入库【" + 2 + "】"); LogInfo("【" + posId + "】出库时，更新盘空满信息 托盘号【" + MoveInfo.MoveParam.TrayNumber + "】，是否有料盘【" + true + "】,出库入库【" + 2 + "】");
TrayManager.UpdateFixtureValue(MoveInfo.MoveParam.TrayNumber, true, 2, bagWidth); TrayManager.UpdateFixtureValue(MoveInfo.MoveParam.TrayNumber, true, 2, MoveInfo.MoveParam.WareCode, MoveInfo.MoveParam.PosId, MoveInfo.MoveParam.PlateH, bagWidth);
}
else
{
int num = TrayManager.GetNum(DeviceID);
LogInfo("【" + posId + "】出库时，更新盘空满信息 托盘号【" + num + "】，是否有料盘【" + true + "】,出库入库【" + 2 + "】");
TrayManager.UpdateFixtureValue(num, true, 2, bagWidth);
}
//出库全部完成 //出库全部完成
lineStatus = LineStatus.StoreOnline; lineStatus = LineStatus.StoreOnline;
MoveInfo.NextMoveStep(LineMoveStep.MO_59_ClampCylinderTighten); MoveInfo.NextMoveStep(LineMoveStep.MO_59_ClampCylinderTighten);
...@@ -256,7 +249,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -256,7 +249,7 @@ namespace OnlineStore.DeviceLibrary
MoveInfo.NextMoveStep(LineMoveStep.MI_10_WaitBox); MoveInfo.NextMoveStep(LineMoveStep.MI_10_WaitBox);
LogInfo("入库【" + posId + "】处理（等待移栽）：(判断box门口没有盘, 且可以入库)，更新盘号【" + num + "】为空盘"); LogInfo("入库【" + posId + "】处理（等待移栽）：(判断box门口没有盘, 且可以入库)，更新盘号【" + num + "】为空盘");
MoveInfo.WaitList.Add(WaitResultInfo.WaitBoxCanReviceTray()); MoveInfo.WaitList.Add(WaitResultInfo.WaitBoxCanReviceTray());
TrayManager.UpdateFixtureValue(num, false, 0); TrayManager.UpdateFixtureValue(num );
//阻挡气缸移动 //阻挡气缸移动
InStoreLog("放托盘（放开阻挡）：SecondStoreMove=MO_09_TopCylinder_Down 物品已移走，顶升气缸1下降）"); InStoreLog("放托盘（放开阻挡）：SecondStoreMove=MO_09_TopCylinder_Down 物品已移走，顶升气缸1下降）");
...@@ -660,20 +653,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -660,20 +653,7 @@ namespace OnlineStore.DeviceLibrary
#endregion #endregion
private void CheckLog(string msg)
{
LogUtil.debug(Name + msg);
}
private void InStoreLog(string msg)
{
string posId = MoveInfo.MoveParam != null ? MoveInfo.MoveParam.PosId : "";
LogUtil.info(Name + "【" + posId + "】" + msg);
}
private void OutStoreLog(string msg)
{
string posId = MoveInfo.MoveParam != null ? MoveInfo.MoveParam.PosId : "";
LogUtil.info(Name + "【" + posId + "】" + msg);
}
} }
} }
source/DeviceLibrary/assemblyLine/ProvidingEquip.cs
...@@ -98,7 +98,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -98,7 +98,7 @@ namespace OnlineStore.DeviceLibrary
SecondMoveInfo.EndMove(); SecondMoveInfo.EndMove();
MoveInfo.EndMove(); MoveInfo.EndMove();
MoveInfo.NewMove(LineMoveType.ReturnHome); MoveInfo.NewMove(LineMoveType.ReturnHome);
UpdownCylinderStartReset(); StartReset();
return true; return true;
} }
...@@ -113,12 +113,12 @@ namespace OnlineStore.DeviceLibrary ...@@ -113,12 +113,12 @@ namespace OnlineStore.DeviceLibrary
MoveInfo.EndMove(); MoveInfo.EndMove();
SecondMoveInfo.EndMove(); SecondMoveInfo.EndMove();
MoveInfo.NewMove(LineMoveType.Reset); MoveInfo.NewMove(LineMoveType.Reset);
UpdownCylinderStartReset(); StartReset();
return true; return true;
} }
private void UpdownCylinderStartReset() private void StartReset()
{ {
MoveInfo.NextMoveStep(LineMoveStep.MH_UpDownCylinder_Up); MoveInfo.NextMoveStep(LineMoveStep.MH_UpDownCylinder_Up);
CylinderMove(MoveInfo, IO_Type.UpDownCylinder_Down, IO_Type.UpDownCylinder_Up); CylinderMove(MoveInfo, IO_Type.UpDownCylinder_Down, IO_Type.UpDownCylinder_Up);
......
source/DeviceLibrary/assemblyLine/ProvidingEquip_Partial.cs
...@@ -19,6 +19,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -19,6 +19,7 @@ namespace OnlineStore.DeviceLibrary
//托盘在两个阻挡内 //托盘在两个阻挡内
if (num > 0) if (num > 0)
{ {
TrayManager.UpdateSWState(Config.SidesWayNum, 2);
SecondMoveInfo.NewMove(LineMoveType.CheckFixture); SecondMoveInfo.NewMove(LineMoveType.CheckFixture);
CheckLog("托盘检测（流水线阻挡）SecondStoreMove：(MIO_03_StopCylinder2Down 阻挡气缸1-1上升）"); CheckLog("托盘检测（流水线阻挡）SecondStoreMove：(MIO_03_StopCylinder2Down 阻挡气缸1-1上升）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_03_StopCylinder2Down); SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_03_StopCylinder2Down);
...@@ -35,6 +36,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -35,6 +36,7 @@ namespace OnlineStore.DeviceLibrary
//托盘在第一个阻挡处 //托盘在第一个阻挡处
SecondMoveInfo.NewMove(LineMoveType.CheckFixture); SecondMoveInfo.NewMove(LineMoveType.CheckFixture);
SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_01_StopCylinder1Down); SecondMoveInfo.NextMoveStep(LineMoveStep.MIO_01_StopCylinder1Down);
TrayManager.UpdateSWState(Config.SidesWayNum, 2);
CheckLog(" 托盘检测：料盘检测 SecondStoreMove（MIO_01_StopCylinder1Down阻挡气缸1-1下降 ，最多等待1秒）"); CheckLog(" 托盘检测：料盘检测 SecondStoreMove（MIO_01_StopCylinder1Down阻挡气缸1-1下降 ，最多等待1秒）");
IOMove(IO_Type.StopCylinder_Down1, IO_VALUE.HIGH); IOMove(IO_Type.StopCylinder_Down1, IO_VALUE.HIGH);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Down1, IO_VALUE.HIGH)); SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.StopCylinder_Down1, IO_VALUE.HIGH));
...@@ -194,12 +196,14 @@ namespace OnlineStore.DeviceLibrary ...@@ -194,12 +196,14 @@ namespace OnlineStore.DeviceLibrary
{ {
CheckLog("托盘放行 SecondStoreMove：(MO_07_WaitCanGo ，移栽2，需要判断是否可以放盘通过,最多等待10000）"); CheckLog("托盘放行 SecondStoreMove：(MO_07_WaitCanGo ，移栽2，需要判断是否可以放盘通过,最多等待10000）");
SecondMoveInfo.NextMoveStep(LineMoveStep.MO_07_WaitCanGo); SecondMoveInfo.NextMoveStep(LineMoveStep.MO_07_WaitCanGo);
if (DeviceID.Equals(2)) //更新横移托盘已处理完成
{ TrayManager.UpdateSWState(Config.SidesWayNum, 1);
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitTime(10000)); //if (DeviceID.Equals(2))
SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitSideWay()); //{
SecondMoveInfo.OneWaitCanEndStep = true; // SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitTime(10000));
} // SecondMoveInfo.WaitList.Add(WaitResultInfo.WaitSideWay());
// SecondMoveInfo.OneWaitCanEndStep = true;
//}
} }
else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MO_07_WaitCanGo)) else if (SecondMoveInfo.MoveStep.Equals(LineMoveStep.MO_07_WaitCanGo))
...@@ -305,7 +309,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -305,7 +309,7 @@ namespace OnlineStore.DeviceLibrary
MoveInfo.NextMoveStep(LineMoveStep.PO_05_WaitBox); MoveInfo.NextMoveStep(LineMoveStep.PO_05_WaitBox);
LogInfo("出料PO_05_WaitBox【" + posId + "】处理（等待可以移栽） 更新盘号【" + num + "】为空盘"); LogInfo("出料PO_05_WaitBox【" + posId + "】处理（等待可以移栽） 更新盘号【" + num + "】为空盘");
MoveInfo.WaitList.Add(WaitResultInfo.WaitBoxCanReviceTray()); MoveInfo.WaitList.Add(WaitResultInfo.WaitBoxCanReviceTray());
TrayManager.UpdateFixtureValue(num, false, 0); TrayManager.UpdateFixtureValue(num );
//阻挡气缸移动 //阻挡气缸移动
InStoreLog("放托盘（放开阻挡）：SecondStoreMove=MO_09_TopCylinder_Down 物品已移走，顶升气缸1下降）"); InStoreLog("放托盘（放开阻挡）：SecondStoreMove=MO_09_TopCylinder_Down 物品已移走，顶升气缸1下降）");
...@@ -354,20 +358,6 @@ namespace OnlineStore.DeviceLibrary ...@@ -354,20 +358,6 @@ namespace OnlineStore.DeviceLibrary
} }
#endregion #endregion
private void CheckLog(string msg)
{
LogUtil.debug(Name + msg);
}
private void InStoreLog(string msg)
{
string posId = MoveInfo.MoveParam != null ? MoveInfo.MoveParam.PosId : "";
LogUtil.info(Name + "【" + posId + "】" + msg);
}
private void OutStoreLog(string msg)
{
string posId = MoveInfo.MoveParam != null ? MoveInfo.MoveParam.PosId : "";
LogUtil.info(Name + "【" + posId + "】" + msg);
}
} }
} }
source/DeviceLibrary/assemblyLine/TrayManager.cs
...@@ -14,8 +14,6 @@ namespace OnlineStore.DeviceLibrary ...@@ -14,8 +14,6 @@ namespace OnlineStore.DeviceLibrary
/// 出库时，可以不下降直接放料盘的宽度 /// 出库时，可以不下降直接放料盘的宽度
/// </summary> /// </summary>
public const int CanPushBagWidth = 7; public const int CanPushBagWidth = 7;
/// <summary> /// <summary>
/// 放在公共地方，方便存取，夹料编码盘列表，key=编码（1-6），value=是否有物品，true=有物品 /// 放在公共地方，方便存取，夹料编码盘列表，key=编码（1-6），value=是否有物品，true=有物品
/// </summary> /// </summary>
...@@ -24,11 +22,11 @@ namespace OnlineStore.DeviceLibrary ...@@ -24,11 +22,11 @@ namespace OnlineStore.DeviceLibrary
/// <summary> /// <summary>
/// 流水线需要的空盘数量 /// 流水线需要的空盘数量
/// </summary> /// </summary>
public static int LineNeedEmptyTrayNum = 0; internal static int LineNeedEmptyTrayNum = 0;
/// <summary> /// <summary>
/// 最大托盘号，必须按照顺序从1到6走过 /// 最大托盘号，必须按照顺序从1到6走过
/// </summary> /// </summary>
public static int MaxTrayNum = 0; internal static int MaxTrayNum = 0;
/// <summary> /// <summary>
/// 托盘错误消息 /// 托盘错误消息
/// </summary> /// </summary>
...@@ -43,23 +41,20 @@ namespace OnlineStore.DeviceLibrary ...@@ -43,23 +41,20 @@ namespace OnlineStore.DeviceLibrary
{ {
LineRunTest = ConfigAppSettings.GetIntValue(Setting_Init.LineRunTest).Equals(1); LineRunTest = ConfigAppSettings.GetIntValue(Setting_Init.LineRunTest).Equals(1);
} }
//public static bool isNeedEmptyTray()
//{
// if (LineRunTest)
public static bool isNeedEmptyTray() // {
{ // return true;
if (LineRunTest) // }
{ // return LineNeedEmptyTrayNum > 0;
return true; //}
} internal static void AddNeedEmptyTrayNum()
return LineNeedEmptyTrayNum > 0;
}
public static void AddNeedEmptyTrayNum()
{ {
Interlocked.Increment(ref LineNeedEmptyTrayNum); Interlocked.Increment(ref LineNeedEmptyTrayNum);
} }
public static void DelNeedEmptyTrayNum() internal static void DelNeedEmptyTrayNum()
{ {
Interlocked.Decrement(ref LineNeedEmptyTrayNum); Interlocked.Decrement(ref LineNeedEmptyTrayNum);
} }
...@@ -70,7 +65,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -70,7 +65,7 @@ namespace OnlineStore.DeviceLibrary
/// </summary> /// </summary>
/// <param name="trayNum">盘号1-6</param> /// <param name="trayNum">盘号1-6</param>
/// <returns>盘上是否有料盘</returns> /// <returns>盘上是否有料盘</returns>
public static bool IsFixTureFull(int trayNum) internal static bool IsFixTureFull(int trayNum)
{ {
lock (fixtureMapLock) lock (fixtureMapLock)
{ {
...@@ -103,17 +98,17 @@ namespace OnlineStore.DeviceLibrary ...@@ -103,17 +98,17 @@ namespace OnlineStore.DeviceLibrary
// } // }
// return false; // return false;
//} //}
public static void UpdateFixtureValue(int trayNum, bool isFull, int inOrOut) //public static void UpdateFixtureValue(int trayNum, bool isFull, int inOrOut)
{ //{
UpdateFixtureValue(trayNum, isFull, inOrOut, 0); // UpdateFixtureValue(trayNum, isFull, inOrOut, 0);
} //}
/// <summary> /// <summary>
/// 更新对应的盘号（1-6）是否有料盘 /// 更新对应的盘号（1-6）是否有料盘
/// </summary> /// </summary>
/// <param name="trayNum"></param> /// <param name="trayNum"></param>
/// <param name="isFull"></param> /// <param name="isFull"></param>
/// <param name="inOrOut">0=无操作，1=入库，2=出库</param> /// <param name="inOrOut">0=无操作，1=入库，2=出库</param>
public static void UpdateFixtureValue(int trayNum, bool isFull, int inOrOut, int bagWidth) internal static void UpdateFixtureValue(int trayNum, bool isFull=false, int inOrOut=0, string wareCode = "", string posId = "", int plateH = 0, int plateW = 0)
{ {
lock (fixtureMapLock) lock (fixtureMapLock)
{ {
...@@ -121,11 +116,16 @@ namespace OnlineStore.DeviceLibrary ...@@ -121,11 +116,16 @@ namespace OnlineStore.DeviceLibrary
{ {
fixtureCodeFullMap[trayNum].IsFull = isFull; fixtureCodeFullMap[trayNum].IsFull = isFull;
fixtureCodeFullMap[trayNum].InOrOutStore = inOrOut; fixtureCodeFullMap[trayNum].InOrOutStore = inOrOut;
fixtureCodeFullMap[trayNum].BagWidth = bagWidth;
fixtureCodeFullMap[trayNum].WareCode = wareCode;
fixtureCodeFullMap[trayNum].PosId = posId;
fixtureCodeFullMap[trayNum].PlateH = plateH;
fixtureCodeFullMap[trayNum].PlateW = plateW;
} }
else else
{ {
TrayInfo fixture = new TrayInfo(trayNum, isFull, inOrOut, bagWidth); TrayInfo fixture = new TrayInfo(trayNum, isFull, inOrOut, wareCode, posId, plateH, plateW);
fixtureCodeFullMap.Add(trayNum, fixture); fixtureCodeFullMap.Add(trayNum, fixture);
} }
} }
...@@ -133,7 +133,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -133,7 +133,7 @@ namespace OnlineStore.DeviceLibrary
/// <summary> /// <summary>
/// 是否还有有料仓的盘 /// 是否还有有料仓的盘
/// </summary> /// </summary>
public static bool IsHasFull() internal static bool IsHasFull()
{ {
foreach (int key in fixtureCodeFullMap.Keys) foreach (int key in fixtureCodeFullMap.Keys)
{ {
...@@ -147,7 +147,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -147,7 +147,7 @@ namespace OnlineStore.DeviceLibrary
/// <summary> /// <summary>
/// 是否还有有料仓正在出库的盘 /// 是否还有有料仓正在出库的盘
/// </summary> /// </summary>
public static bool IsHasFullOutFixture() internal static bool IsHasFullOutFixture()
{ {
foreach (int key in fixtureCodeFullMap.Keys) foreach (int key in fixtureCodeFullMap.Keys)
{ {
...@@ -159,7 +159,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -159,7 +159,7 @@ namespace OnlineStore.DeviceLibrary
return false; return false;
} }
public static bool RightTrayCode(int trayNum, int preTrayNum, bool isCanUpdateMax) internal static bool RightTrayCode(int trayNum, int preTrayNum, bool isCanUpdateMax)
{ {
int defNext = preTrayNum + 1; int defNext = preTrayNum + 1;
if (preTrayNum.Equals(0) || MaxTrayNum.Equals(0) || trayNum.Equals(defNext)) if (preTrayNum.Equals(0) || MaxTrayNum.Equals(0) || trayNum.Equals(defNext))
...@@ -178,7 +178,7 @@ namespace OnlineStore.DeviceLibrary ...@@ -178,7 +178,7 @@ namespace OnlineStore.DeviceLibrary
return false; return false;
} }
public static void UpdateTrayNumError(int errorStoreID, string errorMsg) internal static void UpdateTrayNumError(int errorStoreID, string errorMsg)
{ {
TrayErrorMsg = errorMsg; TrayErrorMsg = errorMsg;
ErrorStoreId = errorStoreID; ErrorStoreId = errorStoreID;
...@@ -196,5 +196,54 @@ namespace OnlineStore.DeviceLibrary ...@@ -196,5 +196,54 @@ namespace OnlineStore.DeviceLibrary
return subType; return subType;
} }
#region 横移状态缓存
internal static Dictionary<int, int> SidesWayStateMap = new Dictionary<int, int>();
internal static object swMapLock = "";
internal static bool CanMoveSidesWay(int swNum)
{
if (SidesWayStateMap.ContainsKey(swNum))
{
if (SidesWayStateMap[swNum].Equals(1))
{
return true;
}
else if (swNum.Equals(1) || swNum.Equals(2))
{
if (SidesWayStateMap[swNum].Equals(0))
{
return true;
}
}
}
return false;
}
/// <summary>
/// 更新横移托盘的处理状态
/// </summary>
/// <param name="swNum">横移编号</param>
/// <param name="value">0=未处理等待中，1=托盘处理完成，可处理横移，2=托盘正在处理中</param>
internal static void UpdateSWState(int swNum,int value)
{
if (swNum <= 0)
{
return;
}
lock (swMapLock)
{
if (SidesWayStateMap.ContainsKey(swNum))
{
SidesWayStateMap[swNum] = value;
}
else
{
SidesWayStateMap.Add(swNum, value);
}
}
}
#endregion
} }
} }
source/DeviceLibrary/deviceLibrary/IO/IOManager.cs
...@@ -88,9 +88,10 @@ namespace OnlineStore.DeviceLibrary ...@@ -88,9 +88,10 @@ namespace OnlineStore.DeviceLibrary
{ {
if (LineManager.allConfigMap.ContainsKey(subType)) if (LineManager.allConfigMap.ContainsKey(subType))
{ {
if (LineManager.allConfigMap[subType].DIList.ContainsKey(ioType)) string newType = ioType.Replace("SW1_", "SW_").Replace("SW2_", "SW_").Replace("SW3_", "SW_").Replace("SW4_", "SW_");
if (LineManager.allConfigMap[subType].DIList.ContainsKey(newType))
{ {
return LineManager.allConfigMap[subType].DIList[ioType]; return LineManager.allConfigMap[subType].DIList[newType];
} }
} }
...@@ -111,9 +112,10 @@ namespace OnlineStore.DeviceLibrary ...@@ -111,9 +112,10 @@ namespace OnlineStore.DeviceLibrary
{ {
if (LineManager.allConfigMap.ContainsKey(subType)) if (LineManager.allConfigMap.ContainsKey(subType))
{ {
if (LineManager.allConfigMap[subType].DOList.ContainsKey(ioType)) string newType=ioType.Replace("SW1_", "SW_").Replace("SW2_", "SW_").Replace("SW3_", "SW_").Replace("SW4_", "SW_");
if (LineManager.allConfigMap[subType].DOList.ContainsKey(newType))
{ {
return LineManager.allConfigMap[subType].DOList[ioType]; return LineManager.allConfigMap[subType].DOList[newType];
} }
} }
......
source/DeviceLibrary/model/StoreStep.cs
...@@ -380,9 +380,9 @@ namespace OnlineStore.DeviceLibrary ...@@ -380,9 +380,9 @@ namespace OnlineStore.DeviceLibrary
#region 横移轨道处理 5000 开始 #region 横移轨道处理 5000 开始
SW00_Wait=5000, SW00_Wait=5000,
/// <summary> /// <summary>
/// 阻挡气缸下降 /// 定位气缸下降
/// </summary> /// </summary>
SW01_StopCylinderDown=5001, SW01_LocationCylinderDown=5001,
/// <summary> /// <summary>
/// 等待轨道1夹具检测信号 /// 等待轨道1夹具检测信号
......
source/DeviceLibrary/model/TrayInfo.cs
...@@ -12,14 +12,22 @@ namespace OnlineStore.DeviceLibrary ...@@ -12,14 +12,22 @@ namespace OnlineStore.DeviceLibrary
public class TrayInfo public class TrayInfo
{ {
public TrayInfo(int trayNum, bool isFull, int inOrOut, int bagWidth) public TrayInfo(int trayNum, bool isFull=false, int inOrOut=0 )
{ {
this.TrayCode = trayNum; this.TrayCode = trayNum;
this.IsFull = isFull; this.IsFull = isFull;
this.InOrOutStore = inOrOut; this.InOrOutStore = inOrOut;
BagWidth = bagWidth;
} }
public TrayInfo (int trayNum, bool isFull , int inOrOut ,string wareCode,string posId,int plateH,int plateW)
{
this.TrayCode = trayNum;
this.IsFull = isFull;
this.InOrOutStore = inOrOut;
this.WareCode = wareCode;
this.PosId = posId;
this.PlateH = plateH;
this.PlateW = plateW;
}
/// <summary> /// <summary>
/// 夹具编码值（1-6） /// 夹具编码值（1-6）
/// </summary> /// </summary>
...@@ -32,10 +40,22 @@ namespace OnlineStore.DeviceLibrary ...@@ -32,10 +40,22 @@ namespace OnlineStore.DeviceLibrary
/// 出库还是入库（有料盘时才有此操作）0=无操作，1=入库，2=出库 /// 出库还是入库（有料盘时才有此操作）0=无操作，1=入库，2=出库
/// </summary> /// </summary>
public int InOrOutStore { get; set; } public int InOrOutStore { get; set; }
/// <summary>
/// 物品二维码信息
/// </summary>
public string WareCode { get; set; }
/// <summary>
/// 位置坐标名（对应配置表的位置）
/// </summary>
public string PosId { get; set; }
/// <summary>
/// 料盘高度
/// </summary>
public int PlateH { get; set; }
/// <summary> /// <summary>
/// 如果是出库，需要记录盘宽，七寸小盘可以累积到托盘上 /// 料盘宽度
/// 只有出库才会有值
/// </summary> /// </summary>
public int BagWidth { get; set; } public int PlateW { get; set; }
} }
} }
source/LoadCVSLibrary/storeConfig/ConfigItemBase.cs
...@@ -85,6 +85,14 @@ namespace OnlineStore.LoadCSVLibrary ...@@ -85,6 +85,14 @@ namespace OnlineStore.LoadCSVLibrary
public class ConfigMoveAxis : ConfigBase public class ConfigMoveAxis : ConfigBase
{ {
/// <summary> /// <summary>
/// 伺服ON的Do信号
/// </summary>
public string ServerOnDO ="" ;
/// <summary>
/// 伺服刹车信号
/// </summary>
public string BreakOnDO = "";
/// <summary>
/// 使用AC伺服时表示串口号，使用康泰克运动版表示板卡名称 /// 使用AC伺服时表示串口号，使用康泰克运动版表示板卡名称
/// </summary> /// </summary>
[CSVAttribute("设备名称")] [CSVAttribute("设备名称")]
......
source/LoadCVSLibrary/storeConfig/config/FeedingEquip_Config.cs
...@@ -145,7 +145,6 @@ namespace OnlineStore.LoadCSVLibrary ...@@ -145,7 +145,6 @@ namespace OnlineStore.LoadCSVLibrary
public int UpdownAxis_HomeAddSpeed { get; set; } public int UpdownAxis_HomeAddSpeed { get; set; }
/// <summary> /// <summary>
/// PRO,0,移栽上下轴走到待机点速度,UpdownAxis_P1Speed,400,,,,, /// PRO,0,移栽上下轴走到待机点速度,UpdownAxis_P1Speed,400,,,,,
/// </summary> /// </summary>
...@@ -157,7 +156,11 @@ namespace OnlineStore.LoadCSVLibrary ...@@ -157,7 +156,11 @@ namespace OnlineStore.LoadCSVLibrary
[ConfigProAttribute("UpdownAxis_DownSpeed", false)] [ConfigProAttribute("UpdownAxis_DownSpeed", false)]
public int UpdownAxis_DownSpeed { get; set; } public int UpdownAxis_DownSpeed { get; set; }
/// <summary>
/// PRO,0,是否是用来出料,IsCanOut,1,,,,,
/// </summary>
[ConfigProAttribute("IsCanOut", false)]
public int IsCanOut { get; set; }
private Dictionary<int, int> UpDownPositionMap = null; private Dictionary<int, int> UpDownPositionMap = null;
public int GetUpdownPosition(int trayHeight) public int GetUpdownPosition(int trayHeight)
...@@ -277,12 +280,18 @@ namespace OnlineStore.LoadCSVLibrary ...@@ -277,12 +280,18 @@ namespace OnlineStore.LoadCSVLibrary
this.Batch_Axis.HomeHighSpeed = this.BatchAxis_HomeHighSpeed; this.Batch_Axis.HomeHighSpeed = this.BatchAxis_HomeHighSpeed;
this.Batch_Axis.HomeLowSpeed = this.BatchAxis_HomeLowSpeed; this.Batch_Axis.HomeLowSpeed = this.BatchAxis_HomeLowSpeed;
this.Batch_Axis.ServerOnDO = IO_Type.BatchAxis_ServoOn;
this.Batch_Axis.BreakOnDO = IO_Type.BatchAxis_BreakOn;
this.UpDown_Axis.TargetSpeed = this.UpdownAxis_TargetSpeed; this.UpDown_Axis.TargetSpeed = this.UpdownAxis_TargetSpeed;
this.UpDown_Axis.AddSpeed = this.UpdownAxis_AddSpeed; this.UpDown_Axis.AddSpeed = this.UpdownAxis_AddSpeed;
this.UpDown_Axis.DelSpeed = this.UpdownAxis_DelSpeed; this.UpDown_Axis.DelSpeed = this.UpdownAxis_DelSpeed;
this.UpDown_Axis.HomeAddSpeed = this.UpdownAxis_HomeAddSpeed; this.UpDown_Axis.HomeAddSpeed = this.UpdownAxis_HomeAddSpeed;
this.UpDown_Axis.HomeHighSpeed = this.UpdownAxis_HomeHighSpeed; this.UpDown_Axis.HomeHighSpeed = this.UpdownAxis_HomeHighSpeed;
this.UpDown_Axis.HomeLowSpeed = this.UpdownAxis_HomeLowSpeed; this.UpDown_Axis.HomeLowSpeed = this.UpdownAxis_HomeLowSpeed;
this.UpDown_Axis.ServerOnDO = IO_Type.UpDownAxis_ServoOn;
this.UpDown_Axis.BreakOnDO = IO_Type.UpDownAxis_BreakOn;
} }
} }
} }
source/LoadCVSLibrary/storeConfig/config/IO_Type.cs
...@@ -628,13 +628,13 @@ namespace OnlineStore.LoadCSVLibrary ...@@ -628,13 +628,13 @@ namespace OnlineStore.LoadCSVLibrary
public static string FL_TopCylinder_Down = "FL_TopCylinder_Down"; public static string FL_TopCylinder_Down = "FL_TopCylinder_Down";
/// <summary> /// <summary>
/// DO FL1阻挡1下降SOL FL_Stop1Down Y165 /// DO FL1阻挡1下降SOL FL_StopCylinder_Down1 Y165
/// </summary> /// </summary>
public static string FL_Stop1Down = "FL_Stop1Down"; public static string FL_StopCylinder_Down1 = "FL_StopCylinder_Down1";
/// <summary> /// <summary>
/// DO FL1阻挡2下降SOL FL_Stop2Down Y166 /// DO FL1阻挡2下降SOL FL_StopCylinder_Down2 Y166
/// </summary> /// </summary>
public static string FL_Stop2Down = "FL_Stop2Down"; public static string FL_StopCylinder_Down2 = "FL_StopCylinder_Down2";
#endregion #endregion
......
支持 Markdown 格式
你添加了 0 人 到此讨论。请谨慎行事。
Finish editing this message first!