Skip to content

孙克 / RC1250-AssemblyLine

转到一个项目
切换导航栏
切换导航栏固定状态
Commit 8642956f 由 LN
选项

修改：料架进入入料装置时中途链条停止转动的现象。

1 个父辈 e1c740c7
内嵌 并排
正在显示 8 个修改的文件 包含 28 行增加 和 40 行删除
source/AssemblyLineClient/记录.txt
......@@ -224,8 +224,8 @@ PRO,0,移栽上下轴流水线取放料详细位置P2,UpDownP2DetialList,0X0=800
修改：料架进入入料装置时中途链条停止转动的现象。
GetDIValue 方法循环查找三次防止报错引起急停。
......
source/DeviceLibrary/assemblyLine/EquipBase.cs
......@@ -314,7 +314,7 @@ namespace OnlineStore.DeviceLibrary
preTrayNum = currTrayNum;
currTrayNum = RFIDManager.GetTrayNum(DeviceID, true);
LogInfo(" [" + trayCount + "] IP [" + RFIDManager.GetRFIP(DeviceID) + "] [" + preTrayNum + "] 当前托盘 [" + currTrayNum + "]");
if (preTrayNum.Equals(currTrayNum))
if (preTrayNum.Equals(currTrayNum)&&currTrayNum>0)
{
TrayManager.TrayErrorMsg =DateTime.Now.ToLongTimeString()+" "+ Name + "托盘号出现错乱：上一个托盘[" + preTrayNum + "] 当前托盘 [" + currTrayNum + "]，连续两个托盘号一样";
LogUtil.error(Name + "托盘号出现错乱：上一个托盘[" + preTrayNum + "] 当前托盘 [" + currTrayNum + "]，连续两个托盘号一样");
......
source/DeviceLibrary/assemblyLine/FeedingEquip.cs
......@@ -768,7 +768,15 @@ namespace OnlineStore.DeviceLibrary
}
//等待200毫秒后停止转动
Thread.Sleep(3000);
if (MoveInfo.MoveType.Equals(LineMoveStep.FI_03_LineStart))
{
LogUtil.info(logName + " 等待3000后, MoveInfo.MoveType= FI_03_LineStart 不需要停止链条转动");
}
else
{
LogUtil.info(logName + "等待3000后，停止链条转动");
IOMove(IO_Type.SL_Line_Run, IO_VALUE.LOW);
}
//料架可离开
AgvClient.SetStatus(Config.AgvInName, "", ClientAction.FinishEnter, ClientLevel.High, true);
Task.Factory.StartNew(delegate
......
source/DeviceLibrary/assemblyLine/FeedingEquip_InStore.cs
......@@ -485,6 +485,7 @@ namespace OnlineStore.DeviceLibrary
//等待指定时间
MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SL_Location_Check, IO_VALUE.HIGH));
MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SL_Line_Run, IO_VALUE.HIGH));
} else if (IOValue(IO_Type.SL_Entry_Check).Equals(IO_VALUE.HIGH))
{
MoveInfo.NextMoveStep(LineMoveStep.FI_03_LineStart);
......@@ -495,6 +496,7 @@ namespace OnlineStore.DeviceLibrary
//等待指定时间
MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(1000));
MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SL_Stop_Check, IO_VALUE.HIGH));
MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SL_Line_Run, IO_VALUE.HIGH));
}
else
{
......
source/DeviceLibrary/assemblyLine/LineBean_Partial.cs
......@@ -298,20 +298,9 @@ namespace OnlineStore.DeviceLibrary
}
if (sidesWayNum.Equals(2) && SW23WaitTrayNum < 0)
{
// LineMoveInfo moveInfo = FeedingEquipMap[104].SecondMoveInfo;
if (SW23_MoveInfo.MoveType.Equals(LineMoveType.None))
{
return true;
//if (moveInfo.MoveType.Equals(LineMoveType.None))
//{
// return true;
//}
//else if (moveInfo.MoveType.Equals(LineMoveType.CheckFixture) &&
// moveInfo.MoveStep >= LineMoveStep.MO_15_WaitCanGo &&
//moveInfo.MoveStep <= LineMoveStep.MO_18_StopCylinder_Back)
//{
// return true;
//}
}
else if (SW23_MoveInfo.MoveStep <= (LineMoveStep.SW12_WaitTrayGo)
&& SW23_MoveInfo.MoveStep >= (LineMoveStep.SW10_WatOutFixture2))
......@@ -325,20 +314,9 @@ namespace OnlineStore.DeviceLibrary
}
else if (sidesWayNum.Equals(4) && SW41WaitTrayNum < 0)
{
// LineMoveInfo moveInfo = FeedingEquipMap[101].SecondMoveInfo;
if (SW41_MoveInfo.MoveType.Equals(LineMoveType.None))
{
return true;
//if (moveInfo.MoveType.Equals(LineMoveType.None))
//{
// return true;
//}
//else if (moveInfo.MoveType.Equals(LineMoveType.CheckFixture) &&
// moveInfo.MoveStep >= LineMoveStep.MO_15_WaitCanGo &&
//moveInfo.MoveStep <= LineMoveStep.MO_18_StopCylinder_Back)
//{
// return true;
//}
}
else if (SW41_MoveInfo.MoveStep <= (LineMoveStep.SW12_WaitTrayGo)
&& SW41_MoveInfo.MoveStep >= (LineMoveStep.SW10_WatOutFixture2))
......@@ -450,8 +428,7 @@ namespace OnlineStore.DeviceLibrary
{
if (IOValue(IO_Type.SW4_TrayCheck).Equals(IO_VALUE.HIGH) && IOValue(IO_Type.SW1_TrayCheck).Equals(IO_VALUE.LOW) &&
TrayManager.LineCanMoveSW(4) )
//TrayManager.LineCanMoveSW(4) && TrayManager.LineCanMoveSW(1))
TrayManager.LineCanMoveSW(4) && TrayManager.LineCanMoveSW(1))
{
if (TrayManager.checkWatch(sw41WaitWatch, TrayManager.SwTrayWaitTime, true))
{
......@@ -469,15 +446,14 @@ namespace OnlineStore.DeviceLibrary
IOValue(IO_Type.SW4_TrayCheck).Equals(IO_VALUE.LOW) &&
IOValue(IO_Type.SW1_TrayCheck).Equals(IO_VALUE.LOW) &&
(DateTime.Now - lastSw4StopDownTime).TotalSeconds > 2 &&
TrayManager.LineCanMoveSW(4))
//TrayManager.LineCanMoveSW(4) && TrayManager.LineCanMoveSW(1))
TrayManager.LineCanMoveSW(4) && TrayManager.LineCanMoveSW(1))
{
if (TrayManager.checkWatch(sw41WaitWatch, TrayManager.SwTrayWaitTime, true))
{
SW41_MoveInfo.NewMove(LineMoveType.InStore);
SW41_MoveInfo.NextMoveStep(LineMoveStep.SW00_Wait);
UpateSw41TrayNum();
SWLog("横移轨道41：检测到SW4_StopCheck， 开始处理托盘 ，更新托盘号 [" + Sw41TrayNum + "] ");
LogUtil.info(Name + "横移轨道41：检测到SW4_StopCheck， 开始处理托盘 ，更新托盘号 [" + Sw41TrayNum + "] ");
//CylinderMove(SW41_MoveInfo, IO_Type.SW4_LocationCylinder_Up, IO_Type.SW4_LocationCylinder_Down);
//CylinderMove(SW41_MoveInfo, IO_Type.SW1_LocationCylinder_Up, IO_Type.SW1_LocationCylinder_Down);
//阻挡气缸下降500毫秒然后上升
......@@ -500,8 +476,7 @@ namespace OnlineStore.DeviceLibrary
//检测到阻挡夹具信号后，阻挡气缸下降，等待有夹具信号，阻挡气缸上升，
//顶升气缸上升到位，开始流水线转动，检测到出口信号后，停止转动，顶升气缸下降，阻挡4下降，盘通过
if (IOValue(IO_Type.SW2_TrayCheck).Equals(IO_VALUE.HIGH) && IOValue(IO_Type.SW3_TrayCheck).Equals(IO_VALUE.LOW) &&
TrayManager.LineCanMoveSW(2) )
//TrayManager.LineCanMoveSW(2) && TrayManager.LineCanMoveSW(3))
TrayManager.LineCanMoveSW(2) && TrayManager.LineCanMoveSW(3))
{
if (TrayManager.checkWatch(sw23WaitWatch, TrayManager.SwTrayWaitTime, true))
{
......@@ -519,15 +494,14 @@ namespace OnlineStore.DeviceLibrary
IOValue(IO_Type.SW2_TrayCheck).Equals(IO_VALUE.LOW) &&
IOValue(IO_Type.SW3_TrayCheck).Equals(IO_VALUE.LOW) &&
(DateTime.Now - lastSw2StopDownTime).TotalSeconds > 2 &&
TrayManager.LineCanMoveSW(2) )
//TrayManager.LineCanMoveSW(2) && TrayManager.LineCanMoveSW(3))
TrayManager.LineCanMoveSW(2) && TrayManager.LineCanMoveSW(3))
{
if (TrayManager.checkWatch(sw23WaitWatch, TrayManager.SwTrayWaitTime, true))
{
SW23_MoveInfo.NewMove(LineMoveType.InStore);
SW23_MoveInfo.NextMoveStep(LineMoveStep.SW00_Wait);
UpateSw23TrayNum();
SWLog("横移轨道23：检测到SW2_StopCheck， 开始处理托盘 ，更新托盘号 [" + Sw23TrayNum + "] ");
LogUtil.info(Name + "横移轨道23：检测到SW2_StopCheck， 开始处理托盘 ，更新托盘号 [" + Sw23TrayNum + "] ");
//CylinderMove(SW23_MoveInfo, IO_Type.SW2_LocationCylinder_Up, IO_Type.SW2_LocationCylinder_Down);
//CylinderMove(SW23_MoveInfo, IO_Type.SW3_LocationCylinder_Up, IO_Type.SW3_LocationCylinder_Down);
//阻挡气缸下降500毫秒然后上升
......@@ -599,7 +573,7 @@ namespace OnlineStore.DeviceLibrary
if (SW41_MoveInfo.MoveStep.Equals(LineMoveStep.SW00_Wait))
{
SW41_MoveInfo.NextMoveStep(LineMoveStep.SW01_StopDown);
SWLog("横移轨道41： 阻挡气缸下降 等待 SW4_StopCheck=0");
LogUtil.info(Name+ "横移轨道41： 阻挡气缸下降 等待 SW4_StopCheck=0");
IOMove(IO_Type.SW4_StopDown, IO_VALUE.HIGH);
SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW4_StopCheck, IO_VALUE.LOW));
//SW41_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(TrayManager.StopDownWaitTime));
......@@ -786,7 +760,7 @@ namespace OnlineStore.DeviceLibrary
if (SW23_MoveInfo.MoveStep.Equals(LineMoveStep.SW00_Wait))
{
SW23_MoveInfo.NextMoveStep(LineMoveStep.SW01_StopDown);
SWLog("横移轨道23：阻挡气缸下降 等待 SW2_StopCheck=0 ");
LogUtil.info(Name+ "横移轨道23：阻挡气缸下降 等待 SW2_StopCheck=0 ");
IOMove(IO_Type.SW2_StopDown, IO_VALUE.HIGH);
SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitIO(IO_Type.SW2_StopCheck, IO_VALUE.LOW));
// SW23_MoveInfo.WaitList.Add(WaitResultInfo.WaitTime(TrayManager.StopDownWaitTime));
......
source/DeviceLibrary/assemblymanager/TrayManager.cs
......@@ -182,7 +182,7 @@ namespace OnlineStore.DeviceLibrary
{
return true;
}
if (equip.SecondMoveInfo.MoveType.Equals(LineMoveType.None))
if (swNum.Equals(2).Equals(false)&& equip.SecondMoveInfo.MoveType.Equals(LineMoveType.None))
{
return true;
}
......@@ -197,7 +197,7 @@ namespace OnlineStore.DeviceLibrary
{
return true;
}
if (equip.SecondMoveInfo.MoveType.Equals(LineMoveType.None))
if (swNum.Equals(4).Equals(false) && equip.SecondMoveInfo.MoveType.Equals(LineMoveType.None))
{
return true;
}
......
source/DeviceLibrary/deviceLibrary/IO/AIOBOX/AIOBOXManager.cs
......@@ -498,6 +498,8 @@ namespace OnlineStore.DeviceLibrary
public override IO_VALUE GetDIValue(string ioIP, byte slaveId, ushort StartAddress)
{
IO_VALUE value = IO_VALUE.LOW;
for (int i = 1; i <= 3; i++)
{
try
{
AIOBOX aioBox = getAIO(ioIP);
......@@ -519,10 +521,12 @@ namespace OnlineStore.DeviceLibrary
value = IO_VALUE.HIGH;
}
}
break;
}
catch (Exception ex)
{
LogUtil.error("GetDIValue [" + ioIP + "] [" + StartAddress + "] 出错：", ex);
LogUtil.error(" 第【"+i+"】次 GetDIValue [" + ioIP + "] [" + StartAddress + "] 出错：", ex);
}
}
return value;
}
......
支持 Markdown 格式
你添加了 0 人 到此讨论。请谨慎行事。
Finish editing this message first!