startFail,启动失败:急停未开,Startup failure: emergency stop not opened,
WaitSingleTimeOut,等待信号{0}={1}超时,Wait signal {0}={1} timeout,
startFailAir,启动失败:没有气压信号,Startup failure: no air pressure signal,
AxisHomeMoveAlarm,运动{0}轴{1}收到原点完成信号，当前位置[{2}]，误差过大，需要报警,The movement {0} axis {1} receives the origin completion signal& the current position [{2}]& the error is too large& it needs to alarm,
AxisMoveAlarm,运动{0}轴{1}目标位置[{2}]当前位置{3}误差过大，需要报警,Movement {0} axis {1} target position [{2}] current position {3} error is too large& need to alarm,
MoveTimeOut,{0}]超时{1}[{2}],{0}]Time out {1}[{2}],
WaitInstoreTimeOut,[{0}]超时[等待可以入库][{1}秒],[{0}] timeout [wait to store][{1} seconds],
startFail,启动失败:急停未开,Startup failure: emergency stop not opened
WaitSingleTimeOut,等待信号{0}={1}超时,Wait signal {0}={1} timeout
startFailAir,启动失败:没有气压信号,Startup failure: no air pressure signal
AxisHomeMoveAlarm,运动{0}轴{1}收到原点完成信号，当前位置[{2}]，误差过大，需要报警,The movement {0} axis {1} receives the origin completion signal& the current position [{2}]& the error is too large& it needs to alarm
AxisMoveAlarm,运动{0}轴{1}目标位置[{2}]当前位置{3}误差过大，需要报警,Movement {0} axis {1} target position [{2}] current position {3} error is too large& need to alarm
MoveTimeOut,{0}]超时{1}[{2}],{0}]Time out {1}[{2}]
WaitInstoreTimeOut,[{0}]超时[等待可以入库][{1}秒],[{0}] timeout [wait to store][{1} seconds]
HasWare,叉子料盘检测有料，请检查,Fork tray full& please check
NoCodeMsg,未扫到二维码，请重新放入料盘,If the qr code is not scanned& please put it back into the material tray
InStoreNoCode,未扫到二维码，需要将料盘送出,The qr code is not scanned& the material plate needs to be sent out
InStoreError,入库库位格式错误:条码[{0}]库位号[{1}],Incorrect format of the library entry: barcode [{0}] library entry number [{1}]
InStoreNoPosition,入库未找到库位:条码[{0}]库位号[{1}],Storage location not found: barcode [{0}] storage location [{1}]
OutStoreError,出库格式错误{0},Providing format error{0}
OutStoreNoPosition,出库未找库位:{0},Storage location not found :{0}
HomeMove,原点返回,Back to home
AbsMove,绝对运动,Abosolute move
WaitIo,IO信号等待,IO wait
WaitTime,时间等待:,Time to wait:
TargetPosition,电钢目标位置:,Target position of electric steel:
trayHeight,料盘高度,Reel height
请先启动料仓！,请先启动料仓！,Please start the system！
保存位置失败！,保存位置失败！,Save position Fail!
警告（叉子在待机位时，才能移动升降轴和旋转轴）,警告（叉子在待机位时，才能移动升降轴和旋转轴）,Warn(move the lifting and rotating axis only when the gripper is stanby)
叉子不在待机位，请先将叉子退回待机位,叉子不在待机位，请先将叉子退回待机位,Gripper not stanby& return the gripper to standby
确定开始自动出入库？,确定开始自动出入库？,Make sure to start automatic storage ？
请输入正确的密码,请输入正确的密码,Enter the right PSW
打开串口失败,打开串口失败,Failed to open serial port
请输入正确的速度,请输入正确的速度,Please enter the correct speed
自动出库：,自动出库：,Auto outbound：
自动入库：,自动入库：,Auto warehousing：
升降轴位置调试：,升降轴位置调试：,Updown-Axis Debug Location
关闭DEBUG,关闭DEBUG,Close DEBUG
开启DEBUG,开启DEBUG,Open DEBUG
关闭DEBUG,关闭DEBUG,Close DEBUG
开启DEBUG,开启DEBUG,Open DEBUG
出库{0}叉子从库位退出后，未检测到料盘有料,出库{0}叉子从库位退出后，未检测到料盘有料,Outgoing {0} after the fork exits from the storage，no material on the tray is detected
