AboutBox1_tableLayoutPanel_labelCompanyName_Text	上海挚锦科技有限公司	Neotel Technology Co., Ltd
AboutBox1_tableLayoutPanel_okButton_Text	确定	Confirm
AxisMoveControl_groupAxis_groupBox2_label2_Text	实际加速度:	Acceleration:
AxisMoveControl_groupAxis_groupBox2_label4_Text	回原状态:	Home Status:
AxisMoveControl_groupAxis_groupBox2_label50_Text	规划模式:	Preset Mode:
AxisMoveControl_groupAxis_groupBox2_label52_Text	规划位置:	Preset Position:
AxisMoveControl_groupAxis_groupBox2_label53_Text	规划速度:	Preset Speed:
AxisMoveControl_groupAxis_groupBox2_label55_Text	实际位置:	Actual Location:
AxisMoveControl_groupAxis_groupBox2_label56_Text	实际速度:	Actual Speed:
AxisMoveControl_groupAxis_groupBox2_lblALM_Text	报警	Alarm
AxisMoveControl_groupAxis_groupBox2_lblBUSY_Text	忙碌	Busy
AxisMoveControl_groupAxis_groupBox2_lblEMG_Text	急停	E-Stop
AxisMoveControl_groupAxis_groupBox2_lblINP_Text	到位	Ready
AxisMoveControl_groupAxis_groupBox2_lblORG_Text	原点	Home Position
AxisMoveControl_groupAxis_groupBox2_lblSvOn_Text	伺服	Servo
AxisMoveControl_groupAxis_groupBox2_lblWARN_Text	警告	Warning
AxisMoveControl_groupAxis_panel1_btnAddMove_Text	点动+	Increase
AxisMoveControl_groupAxis_panel1_btnAxisAMove_Text	绝对运动	Abosolute Motion
AxisMoveControl_groupAxis_panel1_btnAxisReturnHome_Text	原点返回	Back to Origin
AxisMoveControl_groupAxis_panel1_btnAxisRMove_Text	相对运动	Relative Motion
AxisMoveControl_groupAxis_panel1_btnAxisStop_Text	 停止运动	Stop Running
AxisMoveControl_groupAxis_panel1_btnAxisVMove_Text	匀速运动	Uniform Motion
AxisMoveControl_groupAxis_panel1_btnCloseAxis_Text	关闭伺服	Servo OFF
AxisMoveControl_groupAxis_panel1_btnComAlarmClear_Text	清除报警	Clear Alarm
AxisMoveControl_groupAxis_panel1_btnDelMove_Text	点动-	Decrease
AxisMoveControl_groupAxis_panel1_btnOpenAxis_Text	打开伺服	Servo ON
AxisMoveControl_groupAxis_panel1_cmbAxis_Text	旋转机构	Rotating Axis
AxisMoveControl_groupAxis_panel1_label1_Text	点动速度：	Speed Per Step:
AxisMoveControl_groupAxis_panel1_label46_Text	地址:	Add:
AxisMoveControl_groupAxis_panel1_label47_Text	目标速度:	Target Speed
AxisMoveControl_groupAxis_panel1_label48_Text	目标位置:	Set Location:
AxisMoveControl_groupAxis_panel1_label49_Text	AC伺服:	AC Servo:
AxisMoveControl_groupAxis_panel1_label8_Text	实时位置:	Real time Position:
AxisMoveControl_groupAxis_panel1_linkLabel1_Text	复制	Copy
AxisMoveControl_groupAxis_Text	伺服运动	Servo Motion
ConfigControl_btnSavePos_Text	全部保存	Save All
ConfigControl_groupBox3_Text	点位列表	Position List
Form1_tabc_tab_axis_Text	伺服调试	Servo Diagnostic
Form1_tabc_tab_io__IOControls_btn_singledoorckise_Text	料仓门关闭	Material Door Close
Form1_tabc_tab_io__IOControls_btn_singledooropen_Text	料仓门开启	Material Door Open
Form1_tabc_tab_io_Text	IO调试	I/O Diagnostic
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_ledtower_Text	灯塔设置	Signal Tower Setting
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_Text	常规设置	General Setting
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_tp_button_positiontool_Text	库位定位辅助工具	Location Positioning Tool
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_tp_cb_usefixpos_Text	启用校准库位	Location Calibration ON
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_tp_label_tempsensor_Text	温湿度控制器端口:	T/H Controller Port:
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_uC_SetUserPassword1_groupBox1_button_ok_Text	确认修改	Confirm Change
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_uC_SetUserPassword1_groupBox1_label_newpwd_Text	新密码:	New Password:
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_uC_SetUserPassword1_groupBox1_label_newpwd2_Text	重复新密码:	Repeat The New Password:
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_uC_SetUserPassword1_groupBox1_label_oldpwd_Text	旧密码:	Old Password:
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_uC_SetUserPassword1_groupBox1_Text	管理密码设置	Manage Password
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage1_fixtureSizeConfigControl1_button2_Text	删除	Delete
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage1_fixtureSizeConfigControl1_groupBox_add_button1_Text	添加/修改	Add/Edit
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage1_fixtureSizeConfigControl1_groupBox_add_checkBox_fixtureheight_Text	使用治具物理高度(毫米)	Carrier Thickness(mm)
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage1_fixtureSizeConfigControl1_groupBox_add_checkBox_useedremove_Text	弃用条码	Discard Material Code
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage1_fixtureSizeConfigControl1_groupBox_add_label_startword_Text	匹配首字母:	Match Initials:
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage1_fixtureSizeConfigControl1_groupBox_add_label_wxh_Text	对应宽x高(毫米):	WidthxHeight(mm)
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage1_fixtureSizeConfigControl1_groupBox_add_Text	添加或修改	Add/Edit
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage1_Text	治具设置	Carrier Setting
Form1_tabc_tab_setting_Text	相关设置	Related Setting
Form1_tabc_tab_store__uc_boxdebug_groupInout_btn_autoinout_Text	自动库位测试	Cycle Test
Form1_tabc_tab_store__uc_boxdebug_groupInout_btnInStore_Text	入库测试	Loading Testing
Form1_tabc_tab_store__uc_boxdebug_groupInout_btnOutStore_Text	出库测试	Unloading Test
Form1_tabc_tab_store__uc_boxdebug_groupInout_cb_inoutdebugmode_Text	出入库调试模式	Auto Cycle Test Mode
Form1_tabc_tab_store__uc_boxdebug_groupInout_Text	料仓操作	Operation
Form1_tabc_tab_store_Text	库位调试	Location Calibration
Form1_tabc_tabP1_pnl_btn_IgnoreX09_Text	忽略X23错误,并继续运行	Ignore X23 Error And Continue
Form1_tabc_tabP1_pnl_btn_PauseBuzzer_Text	本次暂停警报器响声	Stop Alarm
Form1_tabc_tabP1_pnl_groupBox1_Text	运行状态	Status
Form1_tabc_tabP1_Text	信息	Info.
FrmPassCheck_btn_cancel_Text	取消	Cancel
FrmPassCheck_btn_ok_Text	确定	Confirm
IOControl_groupBox1_btnCloseDO_Text	关闭	OFF
IOControl_groupBox1_btnOpenDo_Text	打开	ON
IOControl_groupBox1_label14_Text	地址:	Add:
IOControl_groupBox1_label5_Text	定时(ms):	Time(ms):
IOControl_groupBox1_Text	DO写入	DO Write
IOControl_groupBox3_Text	DI列表	DI List
IOControl_groupBox4_Text	DO列表	DO List
menuStrip1_关于ToolStripMenuItem_Text	关于	About
menuStrip1_设备操作ToolStripMenuItem_Text	设备操作	Operation
menuStrip1_语言toolStripMenuItem_Text	语言	Language
StorePosControl_btnSavePos_Text	保存	Save
StorePosControl_groupBox3_Text	点位列表	Position List
设备操作ToolStripMenuItem_btn_run_Text	启动	Start
设备操作ToolStripMenuItem_btn_stop_Text	停止	Stop
设备操作ToolStripMenuItem_禁用蜂鸣器ToolStripMenuItem_Text	起用蜂鸣器	Enable Buzzer
设备操作ToolStripMenuItem_退出ToolStripMenuItem_Text	退出	Exit
	中文	英文
Alarm_Buzzer	故障蜂鸣器	Buzzer
Alarm_HddLed	故障指示灯	Error Indicator
AutoRun_HddLed	自动指示灯	Auto Indicator
autotest_inout_equipment	出入库测试	Storage Test
autotest_msg_01	自动出入库过程会再料盘送至出口后自动停止.	Auto Retrieval Will Stop When The Reel Arrived The Unloading Port.
autotest_msg_02	确定开始自动库位测试？\n请确保料仓库位全部为空.	Please Make Sure The Slots Are All Empty Before Start The Location Check.
AxisMoveControl_status_monitor	状态监控	Status Monitor
batch_door_not_close_cant_lock	批量门未关闭无法锁门X07=High	Batch Material Door Not Closed Can Not Lock The Material Door X07=High
before_FrmPositionTool_stopmuchine	运行库位校准程序前,需要先停止料仓的运行	Please Stop Operation Before Location Calibration.
begin_lock_batch_door	开始锁上批量门	Lock Batch Material Door
begin_open_string_door	开始打开料串门	Open Stacker Material Door
begin_singlein	开始单盘入库	Start Single Reel Loading
cant_find_storeposfile	找不到库位配置文件	Material Location Configuration File Not Found
Clamp_Axis_running_cant_singlein	取料机构运转中,无法单盘入库	Single Reel Storage Cannot Be Processed When Clamp Axis Is In Operation.
close_singledoor	关闭单料门	Close Single Reel Material Door.
Comp_Axis	压紧机构	Compression Axis
Comp_P1	压紧机构待机点P1	Compression Axis P1(Standby)
Comp_P2	压紧机构70mm盘压紧点P2	Compression Axis P2(70mm Reel/Comression Position)
Comp_PH_MM	压紧机构库位高点偏移MM	Compression Axis Location High Point Offset MM
Comp_PoToMM	压紧机构每毫米脉冲	Compression Axis Pulse (ms)
connect_fail	未成功连接	Connection Failure
current_status	当前状态:	Current Status:
detect_signal	检测信号	Detection Signal
device_initializing	设备加载中,请稍后...	Loading…
device_isrunning_cant_exit	机器尚在运行,不能退出,请先停止运行.	Cannot Exit During Operation. Please Stop Operation First.
Device_Led	设备照明开启	Light ON
device_pause	暂停运行	Pause
device_resume	恢复运行	Resume
DI_Door_Down	进料口门下降端	Material Door Downward
DI_Door_Limit	后门门禁	Maintenance Door Access
DI_Door_Up	进料口门上升端	Material Door Upward
DI_Laser_detection	激光对点检测	Laser Point Detection
DI_Reset_BTN	复位	Reset
DI_SuddenStop_BTN	急停	E-Stop
DI_TrayCheck_Door	料盘检测1（进料口）	Reel Detection 1(Material Door)
DI_TrayCheck_Fixture	料盘检测2（料叉）	Reel Detection 2(Gripper)
disable_config_mode	停用配置模式	Configuration Mode OFF
DO_Alarm_Buzzer	故障蜂鸣器	Buzzer
DO_Alarm_HddLed	故障指示灯	Error Indicator
DO_AutoRun_HddLed	自动指示灯	Auto Indicator
DO_Device_Led	设备照明开启	Light ON
DO_RunSign_HddLed	待机指示灯	Standby Indicator
DO_StartOrStopBlow	氮气阀门开启	Nitrogen Valve ON
Door_Axis	出料门	Material Door
Door_Length	出料门行程	Material Door Travel
enable_config_mode	启用配置模式	Configuration Mode ON
free	空闲中	Available
FrmPassCheck	请输入密码	Enter PSW:
full_reel	满料串	Full Stacker.
humidity	湿度	Humidity
ignored	已忽略	Skip
in_suddenstop	急停中	In Emergency Mode
InOut_Axis	进出机构	Horizontal Axis
InOut_P1	进出机构待机点P1	Horizontal Axis Standby Point P1
InOut_P2	进出机构单料口P2	Horizontal Axis Single Reel Retrieval Door P2
InOutAxis_Position_P3	进出轴库位点取料点P3	Horizontal Axis P3(Slot/Picking)
instore_reel	入库料串	Store Stacker
iocard_init_fail	IO板卡初始化失败	I/O Controller Initialization Failed
IOSingle_TimerOut	IO信号超时时间（秒）	IO Signal Timeout (s)
ledstate_Alarm	报警	Alarm
ledstate_AlarmStop	停机报警	Shut Down Alarm
ledstate_HomeReset	复位	Reset
ledstate_InOut	出入库中	In Operation
ledstate_Running	运行	Run
ledstate_SystemPause	暂停	Pause
Middle_Axis	旋转机构	Rotating Axis
Middle_Axis_interference_01	进出轴不在待机点时无法移动旋转轴	Rotating Axis Cannot Move When The Horizontal Axis Is Not Standby
Middle_P1	旋转机构待机点P1	Rotating Axis Standby Point p1
Middle_P2	旋转机构单料口P2	Rotating Axis Single Reel Retrieval Door P2
monitor_config_load_fail	加载监控相机配置文件失败:	Fail To Load Camera Configuration File
monitor_config_not_exist	找不到监控相机配置文件	No Camera Configuration File Found
monitor_open_fail	监控相机打开失败	Fail To Start Camera
motion_alarm	运动报警	Motion Alarm
ngdoor	单料口:	Material Door:
not_detect_reel_code	未识别到有效二维码	No Vaild 2D Code.
not_detect_reel_height	未检测到盘宽	No Diameter Detetcted.
not_in_single_prosses	当前没有在等待单盘入库:	No Reel Loading
open_debug_mode	打开调试模式	Start Diagnostic Mode
out_store_free	舱内有出库料盘	Unloading Reel In SMD BOX
out_string	出库料串	Unloading Stacker
please_take_ngdoor_reel	等待取走单口料盘	Please Take The Reel.
reel_not_onposition_cant_manual_in	料盘没有到位,无法手动入库	Reel Is Not In Position, Manual Storage Failed
reel_wait_in_store	料盘等待入库	Reel Is Waiting To Be Stored.
reset_equipment	重置	Reset
reset_press	按下复位按钮.	Please Press The Reset Button
reset_press_with_sudden	急停未解除,按下复位按钮尝试复位安全继电器.	Emergency Mode Not Release. Please Press Reset To Reset Safety Relay.
runbtn_press	按下启动按钮,开始启动.	Please Press The Start Button
runbtn_press_with_sudden	急停中,按下启动按钮,无法启动.	The Equipment Cannot Start During Emergency Process.
RunSign_HddLed	待机指示灯	Standby Indicator
scan_code_timeout	扫码超时	Scan Timeout.
scanning_code	扫码中	Scanning
start	启动	Start
start_auto_test	自动库位测试	Cycle Test
start_device_first	请先启动料仓！	Please Start The SMD BOX！
StartOrStopBlow	氮气阀门开启	Nitrogen Valve ON
stop_auto_test	停止自动库位测试	Stop Auto Cycle Test
stop_inout_test	停止自动库位测试！	Stop Auto Cycle Test!
store_busy_cant_manual_out	料仓正在出入库中,无法手动出库	Cannot Manual Unloading During Operation
store_inout_debug_mode	进出库调试模式	Cycle Test Mode
store_manage_equipment	进出库调度	Storage Management
store_running_cant_inout	料串无法释放,料仓正在出入库中.	Cannot Release Stacker During Operation
string_begin_release	开始释放料串	Start Relase Stacker
string_full_takeout	料串已满请取出	Please Take The Full Stacker.
string_manual_takeout	手动请求取出料串	Manually Request For Stacker 
string_prepare	料串准备中	Preparing Stacker
string_ready_for_get	料串取料准备就绪	Stacker Ready To Pick
string_ready_for_put	料串放料准备就绪	Stacker Ready To Put
string_releasing	料串释放中	Stacker Releading
system_is_running	系统正在运行.	In Operation
system_need_reset	系统需要重置	Please Reset System
system_pause	系统暂停	Pause
system_running_cantmove	系统正在运行,不能手动控制伺服	The Servo Cannot Be Controlled Manually When The System Is Running
tab_axis	伺服调试	Servo Diagnostic
tab_io	IO调试	I/O Diagnostic
tab_log	日志	Log
tab_setting	相关设置	Related Setting
tab_store	库位调试	Location Calibration
table_datetime	时间	Time
table_info	信息	Info.
table_module	模块	Module
table_step	步骤	Steps
taking_code	取料中	Retrieving
temperature	温度	Temperature
tempnhum_sensor_init_fail	温湿度传感器初始化失败,端口:	T/H Sensor Failed To Initialize, Port:
tips	提示	Notice
UpDown_Axis	升降机构	Vertical Axis
UpDown_Axis_interference_01	进出轴不在待机点时无法移动升降轴	Vertical Axis Cannot Move When The Horizontal Axis Is Not Standby
UpDown_P1	升降轴待机点P1	Vertical Axis P1(Standby)
UpDown_P2	升降轴单料口高点P2	Vertical Axis P2(Material Door/High Position )
UpDown_P3	升降轴单料口低点P3	Vertical Axis P3(Material Door/Low Position )
UpDown_PoToMM	升降轴每毫米脉冲	Vertical Axis Pulse/mm
UpDownAxis_IHPosition_P3	升降轴库位入料高点P3	Vertical Axis P3(Slot/Upward)
UpDownAxis_ILPosition_P4	升降轴库位入料低点P4	Vertical Axis P4(Slot/Downward)
wait_detect_reel_height	等待料盘测高	No Thickness Detetcted.
wait_ngdoor_close	等待单料门关闭	Waiting For Material Door Close
wait_put_reel_into_ngdoor	等待阻挡物离开光栅	Waiting For Cover On The Safety Light Curtain To Be Removed.
wait_server_response_pos	等待服务器返回库位	Waiting The Server Return To Location.
wait_server_response_pos_timeout	服务器返回库位超时	Server Return To Location Timeout.
wait_user_select_pos	等待手动选择入库库位	Waiting For Manual Selection For Location.
XAxis_Position_P2	旋转轴位置P2	Rotating Axis P2
Res0001	温湿度传感器[	T/H Sensor
Res0002	本机IP:[	Local IP:[
Res0003	界面	Interface
Res0004	设备未启动	Initialization Failed
Res0005	停机报警	Shut Down Alarm
Res0006	报警	Alarm
Res0007	复位	Reset
Res0008	运行	Run
Res0009	暂停	Pause
Res0010	出入库中	In Operation
Res0011	进出库调度	Storage Management
Res0012	重置	Reset
Res0013	出入库测试	Storage Test
Res0014	升降轴不在单料口,进出轴不可运动	Vertical Axis Is Not At Material Door. Horizontal Axis Cannot Move
Res0015	后侧防护门没有关闭	Back Protective Material Door Is Open
Res0016	压紧轴报警	Compression Axis Error
Res0017	未检测到盘	No Material Detected
Res0018	无信息物料	No Information Material
Res0019	开始入库	Start Loading
Res0020	完成入库	Complete Loading
Res0021	开始出库	Start Unloading
Res0022	完成出库	Complete Unloading
Res0023	请求环形线空托盘失败	Request For Empty Conveyor Pallet Failed
Res0024	等待环形线取走料盘	Waiting For Conveyor To Pick Up Reel
Res0025	开始批量入库	Start Batch Loading
Res0026	系统忙碌,无法批量入库	Busy. Cannot Batch Loading
Res0027	料串正在上升	The Stacker Is Rising.
Res0028	扫码等待夹爪空闲	Scanning Waiting For Gripper
Res0029	出库时料盘未成功放入料串,请检查	Reel Not In Stacker. Please Check
Res0030	料串正在下降	The Stacker Is Falling.
Res0031	 计算盘高：上升前 [	Calculated Reel Thickness: Before Rising [
Res0032	]实时[ 	]Real Time[ 
Res0033	]差值[	]Difference[
Res0034	]系数[	]Coefficient[
Res0035	] 计算后	] After Calculation
Res0036	请先选择运动轴	Please Select Axis.
Res0037	警告 	Warning
Res0038	提示	Notice
Res0039	请先输入正确的速度	Please Enter The Correct Speed.
Res0040	错误码：	Error Code:
Res0041	伺服尚未使能	Servo Not Enable
Res0042	伺服警报状态中	Servo Alarm 
Res0043	无法操作	Unable To Operate.
Res0044	条码首字母不能为空	Initial Character Cannot Be Empty
Res0045	物理厚度	Actual Thickness
Res0046	自动弃用	Automatic Delete
Res0047	信息	Info.
Res0048	时间	Time
Res0049	模块	Module
Res0050	步骤	Steps
Res0051	未启动	Not Activated
Res0052	禁用蜂鸣器	Disable Buzzer
Res0053	起用蜂鸣器	Enable Buzzer
Res0054	升降轴位置调试：	Vertical Axis Position Check 
Res0055	请输入正确的速度	Please Enter The Correct Speed
Res0056.95729a30	旋转或升降轴在运动,进出轴不可运动	Vertical Axis or Rotating Axis is moving,Horizontal Axis Cannot Move.
Res0057	密码不正确请重新输入!	Password Incorrect, Please Re-Enter!
Res0058	状态,优先级从大到小	Status, From High To Low Priority
Res0059	绿灯	Green
Res0060	黄灯	Yellow
Res0061	红灯	Red
Res0062	无动作	Waiting
Res0063	关	OFF
Res0064	开	ON
Res0065	闪烁	Flashing
Res0066	保存成功!	Saved!
Res0067	保存失败!	Save Failed!
Res0068	旧密码不正确!	Old Password Wrong!
Res0069	两次输入的新密码不一致,请确认!	New Password Entered Not The Same, Please Confirm!
Res0070	新密码不能为空!	New Password Cannot Be Empty!
Res0071	密码修改成功!	Password Change Successfully!
Res0072	等待入库物料	Waiting For Loading Material
Res0073.70dccffd	温湿度超限	T&H Exceeded The Limit
Res0074.60c85b4b	轴	Axis
Res0075.0c33436f	绝对运动，目标位置	Absolute Motion, Target Position
Res0076.87979227	等待	Waiting
Res0077.d7647f48	时间等待	Wait Time
Res0078.21157cbf	毫秒	ms
Res0079.3802ba42	ORG信号	ORG Signal
Res0080.f4a8d691	料盘高度	Reel Thickness
Res0081.84e7c741	批量轴上升到上料点	Batch Axis Up To Loading Position
Res0082.ed4de1c6	扫码完成	Scan Completed
Res0083.1bf30741	第{0}次尝试打开轴:{1}	Try To Enable Axis: {1} For {0} Times
Res0084.814c87d5	...伺服忙碌,急停{0}次	... Servo Busy, EM Stop {0} Times
Res0085.226d8802	...使能成功	... Enable Succeed
Res0086.ebec6459	...尝试使能失败	... Enable Failed
Res0087.3cb23f45	伺服连接中…	Servo Connecting...
Res0088.2bf5c941	打开轴	Enable The Axis
Res0089.33d2a704	失败 	Failed
Res0090.cbd5d752	清理报警	Clear Alarm
Res0091.405c5a9e	收到原点完成信号，当前位置[	Received Complete Signal, Current Position [
Res0092.6658614e	误差过大，需要报警	Excessive Errors. Alarm
Res0093.95840864	轴(0)存在报警,清除失败	Axis (0) Alarm, Alarm Clear Failed
Res0094.b5876296	轴(0)存在报警,清除成功	Axis (0) Alarm, Alarm Clear Succeed
Res0122	入库未找到库位：	No Storage Location.
Res0123	出入库轴	Horizontal Axis
Res0124	出入库时料叉{0}检测到有物料无法继续,请检查.	Gripper {0} Detected Mateiral
Res0125	出库时料叉{0}没有检测到物料无法继续,请检查.	Gripper {0} Detected No Mateiral
Res0126	单料门口有料无法放料.	Material At Material Door Area. Cannot Put New Material
Res0127	等待单料口门开启.	Waiting For Material Door Open
Res0128	入库后料叉{0}上任然检测到物料,请检查.	Gripper {0}  Detected Material After Storage Process Complete
Res0145	回原时舱门口有料无法继续	Material Door Full. Cannot Back To Origin
Res0151	料仓忙碌中,无法启动	SMD BOX Not Ready. Cannot Start.
Res0152	收到出库任务,但料叉上有料,无法启动,请检查	Retrieval Task Received. Material On The Gripper. Please Check.
Res0153	料仓正在出入库中,无法出库	Cannot Retrieve During Storage/Retrieval Process.
Res0154	单料口等待料盘离开.	Please Take The Reel.
Res0155	请放入第二盘料.	Please Load The Following Material.
Res0156	服务器连接异常	Server Connection Error
Res0157	等待料盘送到指定位置.	Waiting For Reel To Designated Location
Res0158	等待料盘到达.	Waiting For Reel
Res0159	单料门口没有检测到出库料盘	No Unloading Material Detected
Res0160	出库库位号:	Location No.:
Res0161	等待单料门料盘被取走	Waiting For Material To Be Picked At Material Door
Res0162	空闲中	Available
Res0163	出库中	In Unloading Process
Res0164	入库中	In Loading Process
Res0167	提示	Notice
Res0211	库位表解析错误	Work Order Parse Error
Res0213	请先启动料仓！	Please Start The SMD BOX！
Res0214	停止自动库位测试	Stop Auto Cycle Test
Res0215	自动库位测试	Cycle Test
Res0216	自动出入库过程会再料盘送至出口后自动停止.	Auto Retrieval Will Stop When The Reel Arrived The Unloading Port.
Res0217	入库料盘没有准备好,请先点击[上料准备],无法启动	Loading Material Is Not Ready. Please Click [Loading Ready] First
Res0218	确定开始自动库位测试？\n请确保料仓库位全部为空.	Please Make Sure The Slots Are All Empty Before Start The Location Check.
Res0219	停止自动库位测试！	Stop Auto Cycle Test!