AboutBox1_tableLayoutPanel_labelCompanyName_Text	上海挚锦科技有限公司	Neotel Technology Co., Ltd
AboutBox1_tableLayoutPanel_okButton_Text	确定	Confirm
AxisMoveControl_groupAxis_groupBox2_label2_Text	实际加速度:	Acceleration:
AxisMoveControl_groupAxis_groupBox2_label4_Text	回原状态:	Home Status:
AxisMoveControl_groupAxis_groupBox2_label50_Text	规划模式:	Preset Mode:
AxisMoveControl_groupAxis_groupBox2_label52_Text	规划位置:	Preset Position:
AxisMoveControl_groupAxis_groupBox2_label53_Text	规划速度:	Preset Speed:
AxisMoveControl_groupAxis_groupBox2_label55_Text	实际位置:	Actual Position:
AxisMoveControl_groupAxis_groupBox2_label56_Text	实际速度:	Actual Speed:
AxisMoveControl_groupAxis_groupBox2_lblALM_Text	报警	Alarm
AxisMoveControl_groupAxis_groupBox2_lblBUSY_Text	忙碌	Busy
AxisMoveControl_groupAxis_groupBox2_lblEMG_Text	急停	E-Stop
AxisMoveControl_groupAxis_groupBox2_lblINP_Text	到位	Ready
AxisMoveControl_groupAxis_groupBox2_lblNEL_Text	负极限	Lower Limit
AxisMoveControl_groupAxis_groupBox2_lblORG_Text	原点	Home Position
AxisMoveControl_groupAxis_groupBox2_lblPEL_Text	正极限	Upper Limit
AxisMoveControl_groupAxis_groupBox2_lblSvOn_Text	伺服	Servo
AxisMoveControl_groupAxis_groupBox2_lblWARN_Text	警告	Warning
AxisMoveControl_groupAxis_panel1_btnAddMove_Text	点动+	Increase
AxisMoveControl_groupAxis_panel1_btnAxisAMove_Text	绝对运动	Abosolute Motion
AxisMoveControl_groupAxis_panel1_btnAxisReturnHome_Text	原点返回	Back to Origin
AxisMoveControl_groupAxis_panel1_btnAxisRMove_Text	相对运动	Relative Motion
AxisMoveControl_groupAxis_panel1_btnAxisStop_Text	 停止运动	Stop Running
AxisMoveControl_groupAxis_panel1_btnAxisVMove_Text	匀速运动	Uniform Motion
AxisMoveControl_groupAxis_panel1_btnCloseAxis_Text	关闭伺服	Servo OFF
AxisMoveControl_groupAxis_panel1_btnComAlarmClear_Text	清除报警	Clear Alarm
AxisMoveControl_groupAxis_panel1_btnDelMove_Text	点动-	Decrease
AxisMoveControl_groupAxis_panel1_btnOpenAxis_Text	打开伺服	Servo ON
AxisMoveControl_groupAxis_panel1_cmbAxis_Text	旋转轴	
AxisMoveControl_groupAxis_panel1_label1_Text	点动速度：	Speed Per Step:
AxisMoveControl_groupAxis_panel1_label45_Text	端口号:	Port:
AxisMoveControl_groupAxis_panel1_label46_Text	地址:	Add:
AxisMoveControl_groupAxis_panel1_label47_Text	目标速度:	Target Speed
AxisMoveControl_groupAxis_panel1_label48_Text	目标位置:	Target Location:
AxisMoveControl_groupAxis_panel1_label49_Text	AC伺服:	AC Servo:
AxisMoveControl_groupAxis_panel1_label8_Text	实时位置:	Real time Position:
AxisMoveControl_groupAxis_panel1_linkLabel1_Text	复制	Copy
AxisMoveControl_groupAxis_Text	伺服运动	Servo Motion
ConfigControl_btnSavePos_Text	全部保存	Save All
ConfigControl_groupBox3_Text	点位列表	Position List
Form1_btn_stop_Text	停止	Stop
Form1_tabc_tab_io__IOControls_panel1_button1_Text	Y38 滚筒正转	Conveying Roller Clockwise
Form1_tabc_tab_io__IOControls_panel1_button2_Text	Y39 滚筒反转	Conveying Roller Counter Clockwise
Form1_tabc_tab_io__IOControls_panel1_button3_Text	Y38 滚筒停止	Conveying Roller Stop
Form1_tabc_tab_io__IOControls_panel1_button4_Text	Y42 滚筒正转	Conveying Roller Clockwise
Form1_tabc_tab_io__IOControls_panel1_button5_Text	Y43 滚筒反转	Conveying Roller Counter Clockwise
Form1_tabc_tab_io__IOControls_panel1_button6_Text	Y42 滚筒停止	Conveying Roller Stop
Form1_tabc_tab_io__IOControls_panel1_rfidControl1_groupBox_rfid_button_read_Text	读取	Read
Form1_tabc_tab_io__IOControls_panel1_rfidControl2_groupBox_rfid_button_read_Text	读取	Read
Form1_tabc_tab_setting__SettingControl_panel1_fixtureSizeConfigControl1_button2_Text	删除	Delete
Form1_tabc_tab_setting__SettingControl_panel1_fixtureSizeConfigControl1_groupBox_add_button1_Text	添加/修改	Add/Edit
Form1_tabc_tab_setting__SettingControl_panel1_fixtureSizeConfigControl1_groupBox_add_checkBox_fixtureheight_Text	使用治具物理高度(毫米)	Carrier Thickness(mm)
Form1_tabc_tab_setting__SettingControl_panel1_fixtureSizeConfigControl1_groupBox_add_checkBox_useedremove_Text	弃用条码	Discard Material Code
Form1_tabc_tab_setting__SettingControl_panel1_fixtureSizeConfigControl1_groupBox_add_label_startword_Text	匹配首字母:	Match Initials:
Form1_tabc_tab_setting__SettingControl_panel1_fixtureSizeConfigControl1_groupBox_add_label_wxh_Text	对应宽x高(毫米):	WidthxHeight(mm)
Form1_tabc_tab_setting__SettingControl_panel1_fixtureSizeConfigControl1_groupBox_add_Text	添加或修改	Add/Edit
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_ledtower_Text	灯塔设置	Signal Tower Setting
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_Text	常规设置	General setting
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage_set_tp_chbAutoRun_Text	开机自启动	Auto Power On
Form1_tabc_tab_setting__SettingControl_tabControl1_tabPage1_Text	治具设置	Carrier Setting
Form1_tabc_tab_store__uc_boxdebug_panel1_groupInout_btnInStore_Text	移库测试	Location Changing Test
Form1_tabc_tab_store__uc_boxdebug_panel1_groupInout_cb_inoutdebugmode_Text	出入库调试模式	Auto Cycle Test Mode
Form1_tabc_tab_store__uc_boxdebug_panel1_groupInout_comboBox_from_Text	DoorL3 (流水线放料点)	DoorL3 (MT Loading Position)
Form1_tabc_tab_store__uc_boxdebug_panel1_groupInout_comboBox_to_Text	DoorL3 (流水线放料点)	DoorL3 (MT Loading Position)
Form1_tabc_tab_store__uc_boxdebug_panel1_groupInout_label_from_Text	取料点:	Picking Point:
Form1_tabc_tab_store__uc_boxdebug_panel1_groupInout_label_to_Text	放料点:	Putting Point:
Form1_tabc_tab_store__uc_boxdebug_panel1_groupInout_Text	设备操作	Operation
Form1_tabc_tab_store_Text	位置调试	Location Calibration
Form1_tabc_tabP1_pnl_btn_PauseBuzzer_Text	本次暂停警报器响声	Stop Alarm
Form1_tabc_tabP1_pnl_cb_EnableBuzzer_Text	使用蜂鸣器	Enable Buzzer
Form1_tabc_tabP1_pnl_cb_IgnoreSafecheck_Text	忽略安全光栅	Skip safety light curtain.
Form1_tabc_tabP1_pnl_groupBox1_Text	运行状态	Status
Form1_tabc_tabP1_Text	信息	Info.
FormR_btn_stop_Text	停止	Stop
FormR_tabc_tab_io__IOControlsR_panel1_button1_Text	Y06 滚筒正转	Conveying Roller Clockwise
FormR_tabc_tab_io__IOControlsR_panel1_button2_Text	Y07 滚筒反转	Conveying Roller Counter Clockwise
FormR_tabc_tab_io__IOControlsR_panel1_button3_Text	Y06 滚筒停止	Conveying Roller Stop
FormR_tabc_tab_io__IOControlsR_panel1_button4_Text	Y10 滚筒正转	Conveying Roller Clockwise
FormR_tabc_tab_io__IOControlsR_panel1_button5_Text	Y11 滚筒反转	Conveying Roller Counter Clockwise
FormR_tabc_tab_io__IOControlsR_panel1_button6_Text	Y10 滚筒停止	Conveying Roller Stop
FormR_tabc_tab_io__IOControlsR_panel1_rfidControl1_groupBox_rfid_button_read_Text	读取	Read
FormR_tabc_tab_io__IOControlsR_panel1_rfidControl2_groupBox_rfid_button_read_Text	读取	Read
FormR_tabc_tab_store__uc_boxdebug_panel1_groupInout_btnInStore_Text	移库测试	Location Changing Test
FormR_tabc_tab_store__uc_boxdebug_panel1_groupInout_cb_inoutdebugmode_Text	出入库调试模式	Auto Cycle Test Mode
FormR_tabc_tab_store__uc_boxdebug_panel1_groupInout_comboBox_from_Text	DoorR1 (R1口取料点)	DoorL3 (R1 Loading Position)
FormR_tabc_tab_store__uc_boxdebug_panel1_groupInout_comboBox_to_Text	DoorR1 (R1口取料点)	DoorL3 (R1 Loading Position)
FormR_tabc_tab_store__uc_boxdebug_panel1_groupInout_label_from_Text	取料点:	Picking Point:
FormR_tabc_tab_store__uc_boxdebug_panel1_groupInout_label_to_Text	放料点:	Putting Point:
FormR_tabc_tab_store__uc_boxdebug_panel1_groupInout_Text	设备操作	Operation
FormR_tabc_tab_store_Text	位置调试	Location Calibration
FormR_tabc_tabP1_pnl_btn_PauseBuzzer_Text	本次暂停警报器响声	Stop Alarm
FormR_tabc_tabP1_pnl_cb_EnableBuzzer_Text	使用蜂鸣器	Enable Buzzer
FormR_tabc_tabP1_pnl_cb_IgnoreSafecheck_Text	忽略安全光栅	Skip safety light curtain.
FormR_tabc_tabP1_pnl_groupBox1_Text	运行状态	Status
FormR_tabc_tabP1_Text	信息	Info.
FormStart__Form1_btn_stop_Text	停止	Stop
FormStart__Form1_tabc_tabP1_pnl_btn_PauseBuzzer_Text	本次暂停警报器响声	Stop Alarm
FormStart__Form1_tabc_tabP1_pnl_cb_EnableBuzzer_Text	使用蜂鸣器	Enable Buzzer
FormStart__Form1_tabc_tabP1_pnl_cb_IgnoreSafecheck_Text	忽略安全光栅	Skip safety light curtain.
FormStart__Form1_tabc_tabP1_pnl_groupBox1_Text	运行状态	Status
FormStart__Form1_tabc_tabP1_Text	信息	Info.
FormStart__FormR_btn_stop_Text	停止	Stop
FormStart__FormR_tabc_tabP1_pnl_btn_PauseBuzzer_Text	本次暂停警报器响声	Stop Alarm
FormStart__FormR_tabc_tabP1_pnl_cb_EnableBuzzer_Text	使用蜂鸣器	Enable Buzzer
FormStart__FormR_tabc_tabP1_pnl_cb_IgnoreSafecheck_Text	忽略安全光栅	Skip safety light curtain.
FormStart__FormR_tabc_tabP1_pnl_groupBox1_Text	运行状态	Status
FormStart__FormR_tabc_tabP1_Text	信息	Info.
FormStart_panel1_button_exit_Text	退出	Exit
FormStart_panel1_button_start_Text	全部启动	Start All
FormStart_panel1_button_stop_Text	全部停止	Stop All
IOControl_groupBox1_btnCloseDO_Text	关闭	OFF
IOControl_groupBox1_btnOpenDo_Text	打开	ON
IOControl_groupBox1_label14_Text	地址:	Add:
IOControl_groupBox1_label5_Text	定时(ms):	Time(ms):
IOControl_groupBox1_Text	DO写入	DO Write
IOControl_groupBox3_Text	DI列表	DI List
IOControl_groupBox4_Text	DO列表	DO List
menuStrip1_关于ToolStripMenuItem_Text	关于	About
menuStrip1_设备操作ToolStripMenuItem_Text	设备操作	Operation
menuStrip1_语言toolStripMenuItem_Text	语言	Language
StorePosControl_btnSavePos_Text	保存	Save
StorePosControl_groupBox3_Text	点位列表	Position List
设备操作ToolStripMenuItem_二维码识别调试ToolStripMenuItem_Text	二维码识别调试	2D Code Recognition Calibration
设备操作ToolStripMenuItem_退出ToolStripMenuItem_Text	退出	Exit
Airpressure_Check	气压检测	Pressure Detection
Alarm_Buzzer	故障蜂鸣器（R侧设备）	Error Buzzer(R1)
Alarm_Led	故障指示灯（R侧设备）	Error Indicator(R1)
AutoRun_Single	R侧自动模式	R side Auto Mode
Batch_OutPlateDownMM	出库时每盘料补偿mm	Add additional thickness(mm) during retrieval process.
Batch_OutStoreDownMM	出库时初始下降mm	Descend mm during retrieval process
Batch_P1	R1上料提升机构待机点P1	Lifting Axis P1(R1/Standby)
Batch_P2	R1上料提升机构上料高点P2	Lifting Axis P2(R1/Upward)
Batch_P3	R2上料提升机构待机点P3	Lifting Axis P3(R1/Standby)
Batch_P4	R2上料提升机构上料高点P4	Lifting Axis P4(R1/Upward)
Batch_PoToMM	上料提升机构高度转换系数	Lifting Axis Height Convertion Factor (Batch Axis Pulse mm)
Camera_Led	相机照明（R侧设备）	Camera Lighting(R1)
Comp_Axis	压紧轴	Compression Axis
Comp_P1	压紧轴待机点P1	Compression Axis P1(Standby)
Comp_P2	压紧轴70mm压紧点P2	Compression Axis P2(Compression 70mm)
Comp_PH_MM	压紧轴库位高点偏移毫米	Compression Axis Offset(mm)(Slot/Upward)
Comp_PoToMM	压紧轴每毫米脉冲	Compression Axis Pulse/mm
Device_Led	设备照明（R侧设备）	Equipment Lighting(R1)
ElectricDoor_Check	R侧电器门禁	Door Access(R1)
Fixture_Comp_Check	L料叉物料夹紧确认	Gripper Tight Detection(L)
Fixture_Materiell_Check	L料叉物料检测	Gripper Material Detection(L)
GetReel_Check	R取料机构料盘检测	Reel Dextion(R Horizontal Axis)
InOut_Axis	进出轴	Horizontal Axis
InOut_P1	进出轴待机点P1	Horizontal Axis P1(Standby)
InOutAxis_Position_P3	进出轴库位点取料点P3	Horizontal Axis P3(Slot/Picking)
IOSingle_TimerOut	IO信号超时时间（秒）	IO Signal Timeout (s)
L1_Front_Car_Check	L1料口前端料车检测	Trolley Detection(L1 Loading port front)
L1_Front_String_Check	L1料口前端料框检测	Magazine Detection(L1 Loading port front)
L1_Line_Run	L1料口线体正转	Conveyor Clockwise(L1 Loading port)
L1_Line_Rwd	L1料口线体反转	Conveyor Counter Clockwise(L1 Loading port)
L1_Location_Down	L1料口料框定位下降端	Magazine Dowel Downward(L1 Loading port)
L1_Location_Up	L1料口料框定位上升端	Magazine Dowel Upward(L1 Loading port)
L1_SafetyLightCurtains	L1料口光栅检测	Safety Light Curtain Detection(L1 Loading port)
L1_String_Inplace_Check	L1料口料框到位检测	Magazine In Position Detection(L1 Loading port)
L2_Front_Car_Check	L2料口前端料车检测	Trolley Detection(L2 Loading port front)
L2_Front_String_Check	L2料口前端料框检测	Magazine Detection(L2 Loading port front)
L2_Line_Run	L2料口线体正转	Conveyor Clockwise(L2 Loading port)
L2_Line_Rwd	L2料口线体反转	Conveyor Counter Clockwise(L2 Loading port)
L2_Location_Down	L2料口料框定位下降端	Magazine Dowel Downward(L2 Loading port)
L2_Location_Up	L2料口料框定位上升端	Magazine Dowel Upward(L2 Loading port)
L2_SafetyLightCurtains	L2料口光栅检测	Safety Light Curtain Detection(L2 Loading port)
L2_String_Inplace_Check	L2料口料框到位检测	Magazine In Position Detection(L2 Loading port)
LastTrayAddHeight	最后一盘料补充高度mm	Additional Height mm
Middle_Axis	旋转轴	Rotating Axis
Middle_P1	旋转轴待机点P1	Rotating Axis P1(Standby)
Middle_P2	旋转轴扫码点P2	Rotating Axis P2(Scanning)
PCB料格	PCB料格	PCB Magazine
PizzaBOX料格	PizzaBOX料格	Pizza Box Magazine
R1_Batch_Axis	R1上料提升机构	R1 Lifting Axis
R1_Front_Car_Check	R1料口前端料车检测	Trolley Detection(R1 Loading port front)
R1_Front_String_Check	R1料口前端料串检测	Stacker Detection(R1 Loading port front)
R1_Line_Run	R1料口线体正转	Conveyor Clockwise(R1 Loading port)
R1_Line_Rwd	R1料口线体反转	Conveyor Counter Clockwise(R1 Loading port)
R1_Location_Down	R1料口料串定位下降端	Stacker Dowel Downward(L1 Loading port)
R1_Location_Up	R1料口料串定位上升端	Stacker Dowel Upward(L1 Loading port)
R1_Reel_Location_Check	R1料口料盘定位检测	Reel Detection(R1 Loading port)
R1_SafetyLightCurtains	R1料口光栅检测	Safety Light Curtain Detection(R1 Loading port)
R1_String_Inplace_Check	R1料口料串到位检测	Stacker In Position Detection(R1 Loading port)
R2_Batch_Axis	R2上料提升机构	R2 Lifting Axis
R2_Front_Car_Check	R2料口前端料车检测	Trolley Detection(R2 Loading port front)
R2_Front_String_Check	R2料口前端料串检测	Stacker Detection(R2 Loading port front)
R2_Line_Run	R2料口线体正转	Conveyor Clockwise(R2 Loading port)
R2_Line_Rwd	R2料口线体反转	Conveyor Counter Clockwise(R2 Loading port)
R2_Location_Down	R2料口料串定位下降端	Stacker Dowel Downward(R2 Loading port)
R2_Location_Up	R2料口料串定位上升端	Stacker Dowel Upward(R2 Loading port)
R2_Reel_Location_Check	R2料口料盘定位检测	Reel Detection(R2 Loading port)
R2_SafetyLightCurtains	R2料口光栅检测	Safety Light Curtain Detection(R2 Loading port)
R2_String_Inplace_Check	R2料口料串到位检测	Stacker In Position Detection(R2 Loading port)
Reset_BTN	R侧复位	R1 Reset
Run_Led	自动指示灯（R侧设备）	Auto Indicator(R1)
SafetyLight_Disable	R侧光栅功能解除	Disable Safety Light Curtain(R1)
ShoeBOX料格	ShoeBOX料格	Shoe Box Magazine
Standby_Led	待机指示灯（R侧设备）	Standby Indicator(R1)
Sucker	R取料吸盘取料	Material Gripper(R1)
Suction_Pressure_Check	R取料吸盘压力检测	Material Gripper Compression Test(R1)
SuddenStop_BTN	R侧急停	E-Stop(R1)
Tray料格	Tray料格	Tray Magazine
UpDown_Axis	升降轴	Vertical Axis
UpDown_P1	升降轴待机点P1	Vertical Axis P1(Standby)
UpDown_P2	升降轴扫码点P2	Vertical Axis P2(Scanning)
UpDown_PoToMM	升降轴每毫米脉冲	Vertical Axis Pulse/mm
UpDownAxis_IHPosition_P3	升降轴库位入料高点P3	Vertical Axis P3(Slot/Upward)
UpDownAxis_ILPosition_P4	升降轴库位入料低点P4	Vertical Axis P4(Slot/Downward)
WidthCheck_13	R取料机构叉13寸料盘检测	13in Reel Detection(R Horizontal Axis)
WidthCheck_15	R取料机构15寸料盘检测 右侧进出轴	15in Reel Detection(R Horizontal Axis)
XAxis_Position_P2	旋转轴位置P2	Rotating Axis P2
Res0001	温湿度传感器	T/H Sensor
Res0002	本机IP	Local IP
Res0003	找不到监控相机配置文件	No camera configuration file found
Res0004	加载监控相机配置文件失败:	Fail to load camera configuration file
Res0005	监控相机打开失败	Fail to load camera system
Res0006	设备未启动	Initialization failed
Res0007	入库NG	Storage failed.
Res0008	库位号	Location No.
Res0009	按下复位按钮.	Please press the reset button
Res0010	急停未解除,按下复位按钮尝试复位安全继电器.	Emergency mode not release. Please press the reset to reset safety relay.
Res0011	按下启动按钮,开始启动.	Please press the start button
Res0012	系统正在运行.	In Operation
Res0013	急停中,按下启动按钮,无法启动.	The equipment cannot start during Emergency process.
Res0014	未检测到气压信号.	No air pressure signal detected.
Res0015	停机报警	Shut Down Alarm
Res0016	报警	Alarm
Res0017	复位	Reset
Res0018	运行	Run
Res0019	暂停	Pause
Res0020	出入库中	In Operation
Res0021	找不到库位配置文件	Material location configuration file could not be found.
Res0022	IO板卡初始化失败	I/O controller failed to initialize.
Res0023	打开调试模式	Start Debugging Mode
Res0024	重置	Reset
Res0025	库位测试	Cycle Test
Res0026	L1料口	L1 Material Door
Res0027	L2料口	L2 Material Door
Res0028	移栽机构	Automatic Material Handler
Res0029	进出轴不在待机点时无法移动升降轴	Vertical Axis cannot move when the Horizontal Axis is not standby
Res0030	已忽略	Skip
Res0031	安全光栅被遮挡	Safety Light Curtain is covered.
Res0032	电气门没有关闭	Electrical Door Open
Res0033	系统暂停	Pause
Res0034	急停中	In Emergency Mode
Res0035	系统需要重置	Please reset system
Res0036	进出库调试模式	Cycle Test Mode
Res0037	气压不足	Air pressure is insufficient.
Res0038	运动报警	Motion Alarm
Res0039	批量	Batch
Res0040	收到出库任务,但料叉上有料,无法启动,请检查	Retrieval task received. Material on the gripper. Please check.
Res0041	单盘出库	Single Reel Retrieval
Res0042	出库任务等待关闭批量舱门	Retrival task pending…Waiting for closing material door
Res0043	服务器连接异常	Server Connection Error
Res0044	单料口等待料盘离开.	Please take the reel.
Res0045	等待料盘送到指定位置.	Waiting for reel to designated location
Res0046	等待料盘到达.	Waiting for reel
Res0047	空闲中	Available
Res0048	料仓忙碌中,无法启动	SMD BOX not ready. Cannot start.
Res0049	入库料盘没有准备好,无法启动	Reel not ready. Cannot start.
Res0050	R1料口	R1 Material Door
Res0051	R2料口	R2 Material Door
Res0052	请先选择运动轴	Please select the axis.
Res0053	警告 	Warning
Res0054	提示	Notice
Res0055	请先输入正确的速度	Please enter the correct speed.
Res0056	状态监控	Status monitor
Res0057	错误码：	Error Code:
Res0058	伺服尚未使能	Servo is disabled.
Res0059	伺服警报状态中	Servo alarm 
Res0060	无法操作	Unable to operate.
Res0061	条码首字母不能为空	Initial character cannot be empty
Res0062	物理厚度	Actual Thickness
Res0063	自动弃用	Automatic Delete
Res0064	机器	ML5
Res0065	侧	Side
Res0066	尚未停止运行无法退出.	Cannot exit during operation.
Res0067	尚在运行,不能退出,请先停止运行.	Cannot exit during operation. Please stop operation first.
Res0068	信息	Info.
Res0069	时间	Time
Res0070	模块	Module
Res0071	步骤	Steps
Res0072	设备加载中,请稍后...	Loading…
Res0073	IO调试	I/O Diagnostic
Res0074	伺服调试	Servo Diagnostic
Res0075	位置调试	Location Calibration
Res0076	治具设置	Carrier Setting
Res0077	启用配置模式	Configuration Mode ON
Res0078	停用配置模式	Configuration Mode OFF
Res0079	急停中,无法启动	The SMD BOX cannot be turned on during Emergency Mode
Res0080	恢复运行	Resume
Res0081	暂停运行	Pause
Res0082	启动	Start
Res0083	机器尚在运行,不能退出,请先停止运行.	Cannot exit during operation. Please stop operation first.
Res0084	手动	Manual
Res0085	升降轴位置调试：	Vertical Axis Position Check 
Res0086	检测信号	Detection Signal
Res0087	请输入正确的速度	Please enter the correct speed
Res0088	编号,标准位置,升降轴库位入料高点P3,升降轴库位入料低点P4	
Res0089	系统正在运行,不能手动控制伺服	The servo cannot be controlled manually when the system is running
Res0090	其他取放料口	Other Material Door
Res0091	请先启动料仓！	Please start the SMD BOX！
Res0092	状态,优先级从大到小	Status, From high to low priority
Res0093	绿灯	Green
Res0094	黄灯	Yellow
Res0095	红灯	Red
Res0096	无动作	Waiting
Res0097	关	OFF
Res0098	开	ON
Res0099	闪烁	Flashing
Res0100	保存成功!	Saved!
Res0101	保存失败!	Save failed!
Res0102	 RFID读取失败	
Res0103	开始转移物料时,料叉上检测到有料,无法开始	
Res0104	物料出库后,料叉上没有检测到物料,请检查	
Res0105	未识别到有效二维码,放入NG箱	
Res0108	当前没有料串	No stacker.
Res0109	感应到料串	Stacter is detected
Res0110	料串正在上升	The stacker is rising.
Res0111	料串取料准备就绪	Stacker is prepared to be taken.
Res0112	料串放料准备就绪	Stacker is prepared to be released.
Res0113	料串正在下降	The stacker is falling.
Res0114	料串已满请取出	Please take the full stacker.
Res0115	等待料串被取走	Please take the stacker.
Res0116	空料串	Empty Stacker.
Res0117	满料串	Full Stacker.
Res0118	入库料串	Store Stacker
Res0119	无料串	No stacker.
Res0120	料串准备中	Stacker is being prepared.
Res0121	料串释放中	Stacker is being released.
Res0122	直径	Diameter
Res0123	厚度	Thickness
Res0124	条码	Barcode
Res0183	打开失败	Open failed